- ページ 27

船舶用GPSシステム Garmin GPSMAP 700 SeriesのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Garmin GPSMAP 700 Series 44 ページ。 Flat-mount kit
Garmin GPSMAP 700 Series にも：取付説明書 (10 ページ), クイック・リファレンス・マニュアル (2 ページ), 設定マニュアル (2 ページ), テンプレート (2 ページ), クイック・スタート・マニュアル (4 ページ), オーナーズマニュアル (38 ページ), 取付説明書 (6 ページ), オーナーズマニュアル (50 ページ), 取付説明書 (34 ページ)

ページを印刷する

Clutter caused by rain may still be visible.

Reducing Cross Talk Clutter on the Radar Screen

You can reduce the appearance of clutter caused by

interference from another nearby radar source, when the cross

talk reject setting is on.

NOTE: Depending upon the radar in use, the cross talk reject

setting configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Cross Talk Reject.

Radar Display Settings

From any Radar screen or the Radar overlay, select Menu >

Radar Setup.

Orientation: Sets the perspective of the radar display. The

orientation setting applies to every radar mode. This setting

does not apply to the Radar overlay.

Appearance: Sets the color scheme, look-ahead speed, and

navigation appearance.

Front of Boat: Compensates for the physical location of the

radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Radar Appearance Settings

From a Radar screen, select Menu > Radar Setup >

Appearance.

NOTE: These settings do not apply to the Radar overlay.

Color Scheme: Sets the color scheme.

Look-Ahead Speed: Shifts your present location toward the

bottom of the screen automatically as your speed increases.

Enter your top speed for the best results.

Heading Line: Shows an extension from the bow of the boat in

the direction of travel on the radar screen.

Rings: Shows the range rings that help you to visualize

distances on the radar screen.

Nav. Lines: Shows the navigation lines that indicate the course

you have set using Route To, Guide To, or Go To.

Waypoints: Shows waypoints on the radar screen.

Front-of-Boat Offset

The front-of-boat offset compensates for the physical location of

the radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Measuring the Potential Front-of-Boat Offset

The front-of-boat offset compensates for the physical location of

the radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Using a magnetic compass, take an optical bearing of a

stationary target located within viewable range.

Measure the target bearing on the radar.

If the bearing deviation is more than +/- 1°, set the front-of-

boat offset.

Setting the Front-of-Boat Offset

Before you can set the front-of-boat offset, you must measure

the potential front-of-boat offset.

The front-of-boat offset setting configured for use in one radar

mode is applied to every other radar mode and to the Radar

overlay.

From a Radar screen or the Radar overlay, select Menu >

Radar Setup > Front of Boat.

Select Up or Down to adjust the offset.

Gauges and Almanac Information

Gauges provide various information about the trip, engine,

environment, and wind, and are available on all chartplotter

models. Numbers, Compass, and Trip gauges are available on

all chartplotters. Wind and Environment gauges require valid

wind data from the NMEA 0183 or NMEA 2000 network. Engine

gauges require a connection to the NMEA 2000 network, so

they are not available on all chartplotter models.

The chartplotters also provide almanac information about tides,

currents, and the sun and moon, such as rise and set times.

Viewing the Compass

You can view information about your bearing, heading, and

route using the compass.

Select Gauges > Compass.

Viewing Trip Gauges

Trip gauges show information for odometer, speed, time, and

fuel for your present trip.

Select Gauges > Trip Data.

Resetting Trip Gauges

Select Gauges > Trip Data > Menu.

Select an option:

• To set all the readings for the present trip to zero, select

Reset Trip.

• To set the maximum speed reading to zero, select Reset

Maximum Speed.

• To set the odometer reading to zero, select Reset

Odometer.

• To set all the readings to zero, select Reset All.

Viewing Engine and Fuel Gauges

Before you can view engine and fuel gauges, you must be

connected to a NMEA 2000 network capable of sensing engine

and fuel data. See the installation instructions for details.

Select Gauges > Engine.

Customizing Engine Gauge and Fuel Gauge Limits

You can configure the upper and lower limits and the range of

desired standard operation of a gauge. When a value exceeds

the range of standard operation, the gauge becomes red.

NOTE: Not all options are available for all gauges.

From the engine gauges screen, select Menu > Gauge

Setup > Set Gauge Limits.

Select a gauge.

Select Gauge Limits > Custom > Edit Limits.

Select an option:

• To set the minimum value of the standard operating

range, select Rated Min..

• To set the maximum value of the standard operating

range, select Rated Max..

• To set the lower limit of the gauge lower than the rated

minimum, select Scale Min..

• To set the upper limit of the gauge higher than the rated

maximum, select Scale Max..

Select the limit value.

Repeat steps 4 and 5 to set additional gauge limits.

Enabling Status Alarms for Engine Gauges

You can enable the chartplotter to display engine status alarms.

From the engine gauges screen, select Menu > Gauge

Setup > Status Alarms > On.