- ページ 2
舶用機器 Garmin FUSION XS SeriesのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin FUSION XS Series 6 ページ。 Marine wake tower speakers
Garmin FUSION XS Series にも： 取付説明書 (13 ページ), 取付説明書 (11 ページ), 取付説明書 (6 ページ), インストレーション・インストラクション (4 ページ)
ページを印刷する
Fusion· XS Series Marine Wake Tower Speakers
Installation Instructions
Important Safety Information
.
See the Important Safety and Product Information guide in the product box
for product warnings and other important information.
This device must be installed according to these instructions.
Disconnect the vehicle's or vessel's power supply before beginning to install
this device.
&CAUTION
Continuous exposure to sound pressure levels over 100 dBA may cause
permanent hearing loss. The volume is typically too loud if you cannot hear
people speaking around you. Limit the amount of time you listen at high
volume. If you experience ringing in your ears or muffled speech, stop
listening and have your hearing checked.
To avoid possible personal injury, always wear safety goggles, ear
protection, and a dust mask when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite side of the
surface to avoid damaging the vessel.
It is strongly recommended that you have your audio system installed by a
professional installer to ensure optimum performance.
You must read all installation instructions before beginning the installation.
If you experience difficulty during the installation, go to
www.fusionentertainment.com for product support.
What's In the Box
•
Two wake tower can speakers
Materials and Tools Needed
16 AWG (1.31 mm
2 )
wire (speakers) (Speaker Wire Gauge Guide,
page 2)
20 AWG (0.5 mm
2
)
wire (LEDs)
3 A in-line fuse (LEDs)
Speaker mounting bracket (sold separately)
1
Drill and 12 mm
(11
2
in.) drill bit
Wire strippers
Solder and dual-wall heat-shrink tubing for wire connections
NOTE:
For customized installations, additional tools and materials may be
needed.
Mounting the Speakers
You must purchase mounting brackets for the Fusion XS Series speakers
separately. Each type of mounting bracket contains
specific
installation
instructions.
If necessary, mark the locations on the wake tower or the deck where you
plan to mount the speakers.
2 If necessary, drill a 12 mm
(11
2
in.) cable pass-through hole in the wake
tower or deck.
3 Route the speaker and LED power wires (not included) to the mounting
locations.
4 Using the installation instructions provided with the mounting bracket,
connect the bracket to the speakers and to the wake tower or the deck.
5 Connect the speaker wires (Speaker Wiring, page 2).
6 If necessary, connect the LED power wires (LED Wiring, page 2).
Speaker Wiring
When connecting the speakers to your stereo or amplifier, observe these
considerations.
1
Various brackets are available for mounting these
speakers
on a wake tower bar or on a
deck. See your Fusion dealer for more information.
2
Speaker wire is not included with the
speakers.
You
should
use the
recommended speaker wire to connect the
speakers to the
stereo or
amplifier (Speaker Wire Gauge
Guide, page 2)
.
You should make all wiring
connections using solder and heat-shrink
tubing (not included). You can use
crimp connectors instead of solder
and heat-shrink if the crimp connectors
can be routed through the
bracket and the wake tower
or
your
mounting location, so you should
plan ,ind select the best connection
type for your installation needs.
You can use this table to identify
the polarity of the leads on the
speaker.
Lead color
.
Polarity
White
White with a black stripe
Speaker Wire Gauge Guide
Positive(+)
Negative (·)
You should use 16 AWG (1.31 mm
2 )
speaker wire for most installations. You
can use this table to determine if
you need to use a larger gauge of wire.
This table accounts for terminal
connection
resistance.
NOTE:
If you are using aluminum or tinned
wire, you should use a wire two
gauges larger than the gauge listed below
to compensate for a potential
voltage drop due to the wire material.
4 Ohm Load
(1 Speaker)
Distance between the amplifier
· '
and speaker
.:· ·
From Oto 28 ft. (from Oto 8.5 m)
From 28 to 69 ft. (from 8.5 to
21 m)
2 Ohm Load
(2 Speakers in Parallel)
Distance between the amplifier
·
and speaker
. i 1 !.
From
o
to 14 ft. (from O to 4 m)
From 14 to 35 ft. (from 4
to
10.5
m)
LED Wiring
16AWG
(1.31 mm
2 )
12AWG
(3.31 mm
2 )
16AWG
(1.31 mm
2 )
12AWG
(3.31 mm
2
)
010-12899-00
2
010-12898-00
Recommended
cable
010-12899-00
010-12898-00
It is recommended to install a
Fusion RGB Lighting Control Module with
these speakers to turn the LEDs on
and off, change the colors, and create
lighting effects. See your Fusion dealer
orwww.fusionentertainment.com
for
more information.
You should follow the instructions
provided with the remote control to
connect the LED wires from
the
speakers
to the remote control receiver
module and to connect the receiver
module to power.
If you choose not to install the
remote control, you can set the static color
of
the LEDs by connecting the
colored LED wires directly to the power source
(Connecting the LED Wires, page
2).
Connecting the LED Wires
You can control the color of the LEDs
by connecting the LED color wires to
ground. You can splice the ground wire
to multiple LED wires to customize
the LED color.
NOTE:
Instead of connecting the LED
wires for one dedicated color, you can
install a remote control to turn the
LEDs on and off, change the color,
and
create lighting effects. See your
Fusion dealer or
www.fusionentertainment.com for more
information.
1 Connect a positive wire to the black
wire on the LED cable.
2
Connect a ground wire
to
the
wire on the LED cable according to the
preferred LED color.
LED Color
Red
Green
Red
Green
2
Fusion speaker
cable
is
sold
in
various
lengths.
See your Fusion dealer for more informa-
tion.
Installation Instructions