- ページ 3

舶用機器 Garmin GPSMAP 7015のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin GPSMAP 7015 21 ページ。 Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 7015 にも：オーナーズマニュアル (2 ページ), テクニカル・リファレンス (42 ページ), 重要な安全情報 (48 ページ), 適合宣言 (6 ページ), テンプレートマニュアル (2 ページ), 補足マニュアル (24 ページ)

ページを印刷する

Flush Mounting the GPSMAP 6000/7000 Series Chartplotter

Hardware (included):

• Flush-mount template

• Rubber gasket

• Four flush-mount nut-plates

• Four 60 mm M3 × 0.5 screws (to secure the nut plate to the

mounting surface)

• Four M4 × 0.7 screws (to secure the chartplotter to the nut plate)

• Four 7 mm nylon washers (for the M4 × 0.7 screws)

1. The flush-mount template is included in the product box. Trim the template and ensure that it will fit in the location at which you want to flush

mount the chartplotter.

NotES:

• Ensure that the surface on which you mount the chartplotter has enough open space behind it to accommodate the chartplotter and the

connected wires. Refer to the diagram on the flush-mount template for the clearance-space needed by your chartplotter.

• Ensure that there is at least

flush-mount template.

• Ensure that enough ventilation is present behind the mounting surface to create sufficient air flow to prevent the chartplotter from

overheating.

• To avoid interference, mount GPSMAP 6008/6208 chartplotters 15 in. (38.1 cm), GPSMAP 6012/6212 chartplotters 16 in. (40.6 cm),

GPSMAP 7012/7212 chartplotters 25 in. (63.5 cm) and 7015/7215 chartplotters 17 in. (43.2 cm) from a magnetic compass.

2. The flush-mount template has adhesive on the back. Remove the protective liner and apply the template to the location at which you want to

flush mount the chartplotter.

3. Using a

in. (9.5 mm) drill bit, drill one or more of the four pilot holes inside the corner of the template to begin cutting the mounting

surface.

4. Using a jigsaw, cut the mounting surface along the inside of the solid line indicated on the flush-mount template. Use a file and sandpaper to

refine the size of the hole. Be very careful when cutting this hole. there is only a small amount of clearance between the case and

the mounting holes.

5. Place the chartplotter in the hole and ensure that the mounting holes on the chartplotter line up with the larger

flush-mount template after cutting, sanding, and filing the hole. If they do not line up, mark new locations for the larger holes.

6. Using a center punch, indent the center of each of the larger

7. Using a

in. (7.2 mm) drill bit, drill the four larger holes.

8. Starting in one corner of the template, place a nut plate over the larger hole you drilled in step

7. Ensure that the smaller

on the template. If they do not line up, mark a new location for the smaller hole. Repeat this

step for each corner of the template.

9. Using a center punch, indent the center of each of the smaller

locations.

10. R emove the flush-mount template from the mounting surface.

11. S tarting in one corner of the mounting location, place a nut plate on the back of the mounting

surface, lining up the large and small holes. The raised portion of the nut plate should fit into

the larger hole.

12. S ecure the nut plate to the mounting surface by fastening an included 60 mm M3 × 0.5 screw

through the smaller

in. (3.5 mm) hole.

GPSMAP 6000/7000 Series Installation Instructions

in. (13 mm) of space on the right side of the chartplotter to access the SD card door, as indicated on the

in. (3.5 mm) hole on the nut plate lines up with the smaller hole

tools required (not included):

• Jigsaw

• Scissors

• Drill

• Drill bits—

in. (9.5 mm),

• Number 2 Phillips screwdriver

• Center punch and hammer

• File and sandpaper

in. (7.2 mm) mounting-hole locations.

in. (3.5 mm) mounting-hole

in. (7.2 mm), and

in. (3.5 mm)

in. (7.2 mm) holes on the

Use the 60 mm M3 × 0.5 screw

to fasten the nut plate to the

mounting surface

Use the 70 mm M4 × 0.7 screw

to fasten the chartplotter to the

nut plate

Flush-mount Nut Plate