舶用機器 Garmin GSD 26のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin GSD 26 6 ページ。 Professional sonar module
Garmin GSD 26 にも： 取付説明書 (6 ページ), 取付説明書 (14 ページ)
ページを印刷する
GSD
24/26 Installation Instructions
™
To obtain the best performance and to avoid damage to your boat, install the
Garmin
GSD 24/26 unit according to the following instructions. Professional
®
installation of the unit is highly recommended, because specific knowledge of
boat construction is required to properly install the unit.
Read all installation instructions before proceeding with the installation. If
you experience difficulty during the installation, contact Garmin Product Support.
Registering Your Device
Help us better support you by completing our online registration today.
• Go to http://my.garmin.com.
• Keep the original sales receipt, or a photocopy, in a safe place.
Contacting Garmin Product Support
Contact Garmin Product Support if you have any questions about this product.
• In the USA, go to www.garmin.com/support, or contact Garmin USA by
phone at (913) 397.8200 or (800) 800.1020.
• In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000.
• In Europe, go to
www.garmin.com/support
in-country support.
Important Safety Information
You are responsible for the safe and prudent operation of your vessel. Sonar is
a tool that will enhance your awareness of the water beneath your boat. It does
not relieve you from the responsibility of observing the water around your boat
as you navigate.
When drilling or cutting, always check the opposite side of the surface. Be aware
of fuel tanks, electrical cables, and hydraulic hoses.
Failure to install and maintain this equipment in accordance with these
instructions could result in damage or injury.
Always wear safety goggles, ear protection, and a dust mask when drilling,
cutting, or sanding.
This equipment must be installed by a qualified marine installer.
transducers
A transducer is required to send and receive the sonar signal from the
GSD 24/26. Proper transducer selection and installation are critical to the
operation of the GSD 24/26. Because mounting locations vary, see your local
Garmin dealer or contact Garmin Product Support for more information. Go to
www.garmin.com
to view a full list of transducers.
October 2011
and click Contact Support for
WaRnInG
CautIon
Notice
GSD 24/26 Installation
The GSD 24/26 must be installed according to the following instructions to get
the best possible performance. If you experience difficulty with the installation,
contact Garmin Product Support.
Because every boat is different, you must carefully plan the GSD 24/26 sounder
installation.
1
Select a mounting location
2
Mount the sounder
3
Connect the sounder to the Garmin Marine Network and to power
(page
2).
4
Connect the sounder to the transducer
tools needed
note: If you are not using the mounting hardware included in the kit, use the
most appropriate tool for securing that hardware.
• Drill
• #8 (5 mm) drill bit appropriate for mounting surface
• 1
/
in. (32 mm) paddle drill bit or hole saw appropriate for mounting surface
1
4
• #2 Phillips screwdriver
• 3 mm flat screwdriver
• Cable ties (optional)
• Wire cutter
• Wire stripper
• 1 in. (24 mm) and
• Marine sealant (optional)
Mounting the Sounder
Mounting Location Considerations
• The sounder dimensions and mounting hole locations can be reviewed on
the templates included in the sounder package.
• The sounder must be mounted in a location where it cannot be submerged.
• The sounder must be mounted in a location with adequate ventilation where
it will not be exposed to extreme temperatures.
• The sounder should be mounted in such a way that the LED is visible.
• The sounder should be mounted so that the power and network cables can
be easily connected.
• The sounder should be mounted so that the transducer cable can be
connected. If required, transducer extension cables up to 20 ft. (6 m) are
available through your Garmin dealer.
Mounting the Sounder
1
After you select a mounting location
hardware needed for the surface.
Mounting hardware is included with the sounder, but it may not be suitable
for the mounting surface.
2
If necessary, purchase the mounting hardware.
3
Complete an action:
• Hold the sounder in the intended mounting location and mark the
locations of the mounting holes in the mounting surface, using the
sounder as a template.
• Use the template included with your sounder to mark the locations of the
mounting holes.
4
Drill the mounting holes through the mounting surface.
5
Secure the sounder to the mounting surface using the selected mounting
hardware.
190-00789-02_0C
Notice
(page
1).
(page
1).
(page
2).
/
in. (15 mm) wrenches
19
32
(page
1), determine the mounting
Printed in Taiwan