- ページ 21

ペットケア製品 Garmin Alpha 100 with TT 15 miniのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Garmin Alpha 100 with TT 15 mini 26 ページ。

Garmin Alpha 100 with TT 15 mini オーナーズマニュアル
• For Mac computers, drag the volume icon to the trash.
2
Disconnect the cable from your computer.

Appendix

Accessories and Replacement Parts
Purchasing Accessories
Go to http://buy.garmin.com.
Optional Maps
You can use additional maps with the device, such as BirdsEye
satellite imagery, BlueChart
maps. Detailed maps may contain additional points of interest,
such as restaurants or marine services. For more information,
go to
http://buy.garmin.com
ANT+ Sensors
Your device can be used with wireless ANT+ sensors. For more
information about compatibility and purchasing optional sensors,
go to http://buy.garmin.com.
tempe
The tempe is an ANT+ wireless temperature sensor. You can
attach the sensor to a secure strap or loop where it is exposed
to ambient air, and therefore, provides a consistent source of
accurate temperature data. You must pair the tempe with your
device to display temperature data from the tempe.
Using Optional Fitness Accessories
1
Bring the device within range 10 feet (3 m) of the ANT+
accessory.
2
Select Setup > ANT Sensors.
3
Select Heart Rate Monitor, Bike Cadence Sensor, or
tempe Sensor.
4
Select On, Off, or Search for New.
5
Customize the data fields to view the heart rate or cadence
data
(Customizing the Data Fields, page
Tips for Pairing ANT+ Accessories with Your Garmin Device
• Verify that the ANT+ accessory is compatible with your
Garmin device.
• Before you pair the ANT+ accessory with your Garmin
device, move 10 m (32.9 ft.) away from other ANT+
accessories.
• Bring the Garmin device within range 3 m (10 ft.) of the ANT+
accessory.
• After you pair the first time, your Garmin device automatically
recognizes the ANT+ accessory each time it is activated. This
process occurs automatically when you turn on the Garmin
device and only takes a few seconds when the accessories
are activated and functioning correctly.
• When paired, your Garmin device receives data from only
your accessory, and you can go near other accessories.
Appendix
g2, and City Navigator
detailed
®
®
or contact your Garmin dealer.
12).
TT 15 Battery Replacement Instructions
TT 15 Components
Back plate
Power key
Battery cover
Connectors
Battery
Removing the Old Battery
Before you replace the battery, you must remove all dirt, water,
and debris from the device. You must also have a small Phillips
screwdriver.
1
Remove the six screws from the outer edges of the back
plate.
NOTE: You should leave the two inner screws in place.
2
Pry off the back plate.
3
Disconnect the battery connector and power connector.
4
Remove the screws that secure the battery cover.
5
Remove the battery cover and the battery.
Remember the orientation of the battery. You must install the
new battery the same way.
After you remove the old battery, contact your local waste
disposal department to properly recycle the battery.
Installing the New Battery
Before you replace the battery, you must remove the old battery
(Removing the Old Battery, page
small Phillips screwdriver. You may need a small flat
screwdriver.
1
Install the new battery using the same orientation as the old
battery.
The connector
should face the end nearest the power key,
and the bump
where the wires connect to the battery
should face toward the side with the charging clip contacts.
2
Replace the battery cover.
3
Replace the screws to secure the battery cover.
4
Connect the battery connector and power connector.
You may need to use a flat screwdriver to help secure the
connectors.
17). You also must have a
17