- ページ 7
ペットケア製品 Garmin BarkLimiter 2のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Garmin BarkLimiter 2 10 ページ。
ページを印刷する
When the mode is set in the app, the center LED indicator turns
blue and the smart mode option becomes available after you
cycle through the standard corrections. You must press the
button to see the current mode. When a correction is issued in
smart mode, the corresponding LED indicates your selected
correction.
You can select a standard or smart mode.
1
Remove the collar band from the device.
2
Press the mode button until the green LED indicates the
current mode.
3
Press the mode button within two seconds to cycle the green
LED through the modes, and select a mode.
NOTE: When the center LED is blue, you can select smart
mode.
After two seconds, the LED turns from green to red, and the
device issues a sample correction of your selected mode.
When you select stimulation mode, the device does not issue
a sample correction.
If the device is in smart mode, the blue LED cycles to a
green, then a red LED on the selected correction mode.
Status LED Indicator
The center status LED indicators flashes when the device
detects a bark or has a low battery charge.
LED Activity State
Flashing white
Flashing red
Correction mode A bark was detected, and a
After a correction The battery is low.
Correction Methods
Stimulation: Applies a brief stimulation. You can manually
adjust the stimulation intensity level using the Garmin Canine
app.
Tone: Activates an audible tone. A tone can provide a patterned
interruption to stop a behavior. The tone can be more
effective when it is already associated with a negative
consequence or alternate behavior.
Vibration: Applies a vibration to the dog for a short period of
time to help break focus on the current cause of a behavior.
The effectiveness of the vibration may vary based on the
dog's temperament and experience.
Automatic Intensity
The device can set the stimulation intensity level automatically
based on the barking behavior of the dog. The device starts at
the lowest intensity level and increases the intensity level
gradually until the dog stops barking. When the dog is quiet, the
intensity decreases over time.
The automatic intensity feature is designed to eliminate
excessive nuisance barking. To stop barks sooner, you should
set the intensity level manually.
The extended panic guard is a safety feature that disables
stimulation after four corrections at the highest level, with 10
seconds between corrections. After the fourth correction, the
device waits until no barks are detected in 2 minutes.
NOTE: When you set a fixed correction level, the device does
not enter extended panic guard, even at the highest level of
correction.
Choosing the Correct Intensity Level
You should choose the lowest intensity level that discourages
the dog from barking. If you have never used a bark correction
collar with the dog, the dog requires time and experience to
learn that the bark is the cause of the correction.
Troubleshooting
Status
A bark was detected, and no
correction was applied.
correction was applied.
1
From the Garmin Canine app, set the intensity to the lowest
level.
2
For thirty minutes, when the dog barks, observe the dog for a
reaction, such as a head shake, neck movement, a change in
the way the dog barks, or just a change in expression.
3
If there is no reaction, increase the intensity by one level until
the dog has a slight but recognizable reaction to the
stimulation.
4
Allow 24 hours for the dog to learn to respond by not barking.
5
If the dog continues barking while wearing the collar,
increase the intensity level gradually until you find the level
that discourages the dog from barking.
Troubleshooting
The bark detection is too sensitive
If the BarkLimiter feature activates when the dog is not barking,
or if the bark detection appears to be too sensitive, you can try
these tips.
• Use the Garmin Canine app to adjust the amount of barking
allowed before correcting your dog.
• Use the Garmin Canine app to turn off the BarkLimiter
feature during heavy play, when the dog is very active, or
when the dog is eating.
• Remove all other collars, tags, or other items from your dog.
My dog collar device is not responding
If the dog collar device stops responding, you can try these tips.
• Verify the dog collar device is turned on
Collar Device, page
1).
• Enable Bluetooth wireless technology on your smartphone.
• Pair the dog collar device with your smartphone
Smartphone with the Dog Collar Device, page
• Confirm that you are the only user currently attempting to
train the dog.
NOTE: Only one smartphone can be connected to the dog
collar device at a time.
• Check the battery level of the dog collar device in the Garmin
Canine app.
NOTE: You should sync your dog collar device with the
Garmin Canine app to view updated information and battery
level notifications.
• Hold the power key for 10 seconds to reset the dog collar
device.
My device does not seem to be active
When the device is active, the selected mode LED flashes only
when the device detects a bark, or you press the button.
• Verify the collar is turned on
Device, page
1).
• Verify in the Garmin Canine app that the battery is not low.
• Remove the device from the dog, and press the mode button.
The device flashes the current battery status. If the LED is
red, or the device does not respond, charge the device
(Charging the Dog Collar Device, page
My device is not charging or does not hold a
charge
If the device does not seem to be charging or holding a charge,
you can try these tips.
• Verify the charging connections are secure
Dog Collar Device, page
• Verify the AC adapter and outlet are functional.
(Turning On the Dog
(Pairing Your
1).
(Turning On the Dog Collar
1).
(Charging the
1).
3