- ページ 2

オール・イン・ワン・プリンター Brother MFC9320DWのPDF セットアップ方法をオンラインで閲覧またはダウンロードできます。Brother MFC9320DW 4 ページ。 Wireless setup instructions for mac

ページを印刷する

Wireless Setup Instructions for Mac

Authentication with WEP Encryption:

Choose Shared Key and press OK. Go to step 7.

Authentication with WPA/WPA2-PSK (TKIP

or AES) Encryption:

Choose WPA/WPA2-PSK and press OK. Go to step

Authentication with LEAP:

Choose LEAP, press OK. Go to step 9.

Authentication with EAP-FAST/NONE, EAP-

FAST/MS-CHAPv2, EAP-FAST/GTC (TKIP or

AES Encryption):

Choose EAP-FAST/NONE, EAP-FAST/MSCHAP

(EAP-FAST/MSCHAPv2) or EAP-FAST/GTC, press

OK. Go to step 10.

Choose the appropriate key number and press

OK. Enter the WEP key using the dial pad to

choose each letter or number.

For example, to enter the letter a, press the 2 key

on the dial pad once. To enter the number 3,

press the 3 key on the dial pad seven times.

The letters appear in this order: lower case, upper

case and then numbers.

Press OK when you have entered all the

characters, then press 1

Press ▲ or ▼ to choose TKIP or AES for

Encryption Type? and press OK. Enter the

WPA/WPA2-PSK password using the dial pad to

choose each letter or number. For example, to

enter the letter a, press the 2 key on the dial pad

once. To enter the number 3, press the 3 key on

the dial pad seven times. The letters appear in

this order: lower case, upper case and then

numbers.

Press OK when you have entered all the

characters, then press 1 for Yes to apply your

settings. Go to step 11.

Enter the user name and press OK. You can

use ◄ and ► to move the cursor. For example, to

enter the letter a, press the 2 key on the dial pad

once. Enter the password and press OK, and then

press 1 to apply your settings. Go to step 11.

Press ▲ or ▼ to choose TKIP or AES for

Encryption Type? and press OK. Enter the user

name and press OK. You can use ◄ or ► to move

the cursor. For example, to enter the letter a,

press the 2 key on the dial pad once.

Enter the password and press OK, and then press

1 to apply your settings. Go to step 11.

wireless network using the information you have

entered. If successful, Connected will appear

briefly on the LCD.

If your machine does not successfully connect to

your network, verify your network settings, then

repeat steps 1 to 10 to make sure you have

entered the correct information.

If your access point does not have DHCP enabled

you will need to manually configure the IP

address, subnet mask and gateway of the

machine to suit your network. See the Network

User's Guide for details.

point/router.

Install the drivers & software (Mac OS X

10.3.9 or greater)

Make sure your machine is connected to the

power and your Macintosh is ON. You must be

logged on with Administrator rights.

ImportantIMPORTANT



Note:

Before installation, if you are using personal

firewall software, disable it. After the installation,

restart your personal firewall software.

drive.

www.brother-usa.com

Your machine will now try to connect to your

Wireless setup is now complete. A four

level indicator at the top of your

machine's LCD will show the wireless

signal strength of your access

If there are any programs running, close

them.

Make sure there are no memory cards or a

USB Flash memory drive inserted into the

machine.

The screens may differ depending on your

operating system.

Put the supplied CD-ROM into your CD-ROM