- ページ 2

ノートパソコン Fujitsu LifeBook P702のPDF バイオマニュアルをオンラインで閲覧またはダウンロードできます。Fujitsu LifeBook P702 36 ページ。 Lifebook e/p/s/u series
Fujitsu LifeBook P702 にも： スタートマニュアル (7 ページ)

ページを印刷する
Fujitsu LifeBook P702 バイオマニュアル
L I F E B O O K E / P / S / U B I O S G u i d e
E/P/S/U Series BIOS

BIOS SETUP UTILITY

The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your BIOS is
set at the factory for normal operating conditions,
therefore there is no need to set or change the BIOS
environment to operate your notebook.
The BIOS Setup Utility configures:
•
Device control feature parameters, such as
changing I/O addresses and boot devices.
•
System Data Security feature parameters, such as
passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility, do the following:
1. Turn on or restart your notebook.
2. Press [F2] once the Fujitsu logo appears on the
screen. This will open the main menu of the BIOS
Setup Utility with the current settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key to
scroll through the other setup menus to review or
alter the current settings.
Navigating through the Setup Utility
The BIOS setup utility consists of six menus: Info,
System, Advanced, Security, Boot, and Exit. This docu-
ment explains each menu in turn, including all
submenus and setup items.
The following procedures allow you to navigate the
setup utility menus:
1. To select a menu, use the cursor keys:
2. To select a field within a menu or a submenu, use
the cursor keys:
[ ], [ ].
3. To select the different values for each field, press
the [Spacebar] or [+] to change to the next lower
selection and [F5] or [-] to go to the next higher
selection.
4. To activate a submenu press the [Enter] key.
5. To return to a menu from a submenu, press the
[Esc] key.
6. To go to the Exit menu from any other menu, press
the [Esc] key.
2
7. Pressing the [F9] key resets all items in the BIOS to
the default values.
8. Pressing the [F10] key saves the current configura-
tion and exits the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.
9. Pressing the [F1] key gives you a general help
screen.
Entering the Setup Utility After a Configuration
Change or System Failure
If there has been a change in the system configuration
that does not agree with the parameter settings stored
in your BIOS memory, or there is a failure in the
system, the system beeps and/or displays an error
message after the Power On Self Test (POST). If the
failure is not too severe, it will give you an opportunity
to modify the setup utility settings, as described in the
following steps:
1. When you turn on or restart the computer there is
a beep and/or the following message appears on
the screen:
Error message - please run SETUP program Press
[
], [
].
<F1> key to continue, <F2> to run SETUP
2. If an error message is displayed and you want to
continue with the boot process and start the oper-
ating system anyway, press the [F1] key.
Selecting a field causes a help message
about that field to be displayed on the
right-hand side of the screen.
Pressing the Enter key with the highlight
on a selection that is not a submenu or
auto selection will cause a list of all
options for that item to be displayed.
Pressing the Enter key again will select the
highlighted choice.
If your notebook emits a series of beeps
that sounds like a code and the display is
blank, please refer to the Troubleshooting
Section in the system User's Guide. The
Troubleshooting Section includes a list of
error messages and their meanings.
If your data security settings require it, you
may be asked for a password before the
operating system will be opened.