- ページ 5

プリントサーバー Brother HL-2700CN SeriesのPDF クイック・セットアップ・マニュアルをオンラインで閲覧またはダウンロードできます。Brother HL-2700CN Series 36 ページ。 Quick setup guide - english
Brother HL-2700CN Series にも：クイック・セットアップ・マニュアル (36 ページ)

ページを印刷する

FDA Regulations (100 to 120 volt Model Only)

U.S. Food and Drug Administration (FDA) has implemented regulations for

laser products manufactured on and after August 2, 1976. Compliance is

mandatory for products marketed in the United States. One of the following

labels on the back of the printer indicates compliance with the FDA

regulations and must be attached to laser products marketed in the United

States.

MANUFACTURED:

Brother Industries, Ltd.,

15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan

This product complies with FDA radiation performance standards, 21

CFR subchapter J.

☛ Caution:

Use of controls, adjustments or performance of

procedures other than those specified in this manual may

result in hazardous radiation exposure.

IEC 60825 specification (220 to 240 volt model only)

This printer is a Class 1 laser product as defined in IEC 60825 specifications.

The label shown below is attached in countries where it is needed.

CLASS 1 LASER PRODUCT

APPAREIL À LASER DE CLASSE 1

LASER KLASSE 1 PRODUKT

This printer has a Class 3B laser diode which produces invisible laser

radiation in the scanner unit. You should not open the scanner unit under any

circumstances.

☛ Caution:

Use of controls or adjustments or performance of

procedures other than those specified in this User's Guide

may result in hazardous radiation exposure.

For Finland and Sweden

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

☛ Varoitus!

Laitteen käyttäminen muulla kuin tässä käyttöohjeessa

mainitulla tavalla saattaa altistaa käyttäjän

turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteilylle.

☛ Varning

Om apparaten används på annat sätt än i denna

Bruksanvisning specificerats, kan användaren utsättas för

osynlig laserstrålning, som överskrider gränsen för

laserklass 1.

Internal laser radiation

Maximum radiation power: 5 mW

Wave length:

780 - 800 nm

Laser class:

Class IIIb

(Accordance with 21 CFR Part 1040.10)

Class 3B

(Accordance with IEC 60825)

IMPORTANT - For Your Safety

To ensure safe operation the supplied three-pin plug must be inserted only

into a standard three-pin power outlet that is properly grounded through the

normal household wiring.

Extension cords used with this printer must be three-pin plug type and

correctly wired to provide proper grounding. Incorrectly wired extension

cords may cause personal injury and equipment damage.

The fact that the equipment operates satisfactorily does not imply that the

power is grounded and that the installation is completely safe. For your

safety, if in any doubt about the effective grounding of the power, call a

qualified electrician.

Disconnect device

You must install this printer near a power outlet that is easily accessible. In

case of an emergency, you must disconnect the power cord from the power

outlet to shut off the power completely.

Caution for LAN connection

Connect this product to a LAN connection that is not subjected to over

voltages.

IT power system (For Norway only)

This product is also designed for an IT power system with phase-to-phase

voltage 230V.

Geräuschemission / Acoustic noise emission (for Germany

only)

Lpa < 70 dB (A) DIN 45635-19-01-KL2

Wiring information (for UK)

Important

If you need to replace the plug fuse, fit a fuse that is approved by ASTA to

BS1362 with the same rating as the original fuse.

Always replace the fuse cover. Never use a plug that does not have a cover.

Warning - This printer must be earthed.

The wires in the mains lead are coloured in line with the following code:

Green and Yellow:

Earth

Blue:

Neutral

Brown:

Live

If in any doubt, call a qualified electrician.