プリントサーバー Brother HL-5450DNのPDF クイック・セットアップ・マニュアルをオンラインで閲覧またはダウンロードできます。Brother HL-5450DN 2 ページ。 Zlt
Brother HL-5450DN にも：ユーザーマニュアル (23 ページ), クイック・セットアップ・マニュアル (2 ページ), インストレーション・マニュアル (16 ページ), 製品安全マニュアル (23 ページ)

ページを印刷する

ENG

Version 0

(EU Only)

Unpack the machine and check the components

•

Start Here

•

WARNING indicates a potentially

WARNING

hazardous situation which, if not avoided,

USB cable

could result in death or serious injuries.

It is recommended to use a USB 2.0 (Type A/B) interface cable that is no longer than 2 meters

CAUTION indicates a potentially

(6 feet).

CAUTION

hazardous situation which, if not avoided,

Parallel cable (HL-5440D only)

may result in minor or moderate injuries.

DO NOT use a parallel interface cable that is longer than 2 meters (6 feet). Use a shielded

interface cable that is IEEE 1284‑compliant.

Network cable (HL-5450DN(T) only)

Use a straight‑through Category 5 (or greater) twisted‑pair cable for 10BASE‑T or 100BASE‑TX

Fast Ethernet Network.

Remove the packing material from the machine

Important

DO NOT plug in the AC power cord yet.

Remove the packing tape from the outside of the machine.

Open the MP tray a, and remove the packing tape b from the MP tray

support, then close the MP tray.

Load paper in the paper tray

Pull the paper tray completely out of the machine.

While pressing the green paper‑guide release lever a, slide the paper guides

to fit the paper size you are loading in the tray. Make sure that the guides are

firmly in the slots.

Print a test page

Important

DO NOT connect the Interface cable yet.

Connect the AC power cord to the machine and then connect it to an AC power

outlet.

Thank you for choosing Brother, your support is important to us and we value your business. Your Brother product is

engineered and manufactured to the highest standards to deliver reliable performance, day‑in and day‑out.

Please read the Product Safety Guide first, then read this Quick Setup Guide for the correct setup and installation

procedure. To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/.

Note: Not all models are available in all countries.

Note

The components included in the box may differ depending on your country.

We recommend that you save the original packaging.

If for any reason you must ship your machine, carefully repack the machine in the original

packaging to avoid any damage during transit. The machine should be adequately insured with

the carrier. For how to repack the machine, see Packing and shipping the machine in the User's

Guide.

Illustrations in this Quick Setup Guide are based on the HL‑5450DN.

The interface cable is not a standard accessory. Buy the appropriate interface cable for the

connection you want to use (USB, parallel (HL‑5440D only) or Network (HL‑5450DN(T) only)).

Product Safety Guide

Press the front cover release button and open the front cover. Remove the

silica gel pack a.

CAUTION

DO NOT eat the silica gel pack. Please throw away. If ingested, seek medical attention

immediately.

Note

For Legal or Folio size paper, press the

release button a in the bottom of the

paper tray and then pull out the back of

the paper tray. (Legal or Folio size paper

are not available in some regions.)

Fan the stack of paper well to avoid paper jams and misfeeds.

Turn the machine's power switch on.

After the machine has finished warming up, the Ready LED stops blinking and

stays green.

WARNING

•

Plastic bags are used in the packing of your machine. Plastic bags are not toys. To

avoid the danger of suffocation, keep these bags away from babies and children

and dispose of them correctly.

Drum Unit and Toner

Quick Setup Guide

•

If you use a Lower Tray, DO NOT carry the machine with the Lower Tray as you may

Cartridge Assembly

be injured or cause damage to the machine because it is not attached to the Lower

(pre‑installed)

Tray.

Note

Keep a minimum gap around the machine as shown in the illustration.

AC Power Cord

Installer CD-ROM

150 mm

(6 in.)

Take out the drum unit and toner

Hold the drum unit and toner cartridge

cartridge assembly.

assembly level with both hands and

gently shake it from side to side

several times to distribute the toner

evenly inside the cartridge.

Remove the orange protective

Put the drum unit and toner cartridge

material from the drum unit and toner

assembly firmly back in the machine.

cartridge assembly.

Close the front cover of the machine.

Put the paper in the tray and make sure:

Put the paper tray firmly back in the machine. Make sure that it is completely



The paper is below the maximum paper mark (▼▼▼) a. Over filling the

inserted into the machine.

paper tray will cause paper jams.

Lift up the support flap a to prevent paper from sliding off the face‑down output

The side to be printed on is face down.



tray.



The paper guides touch the sides of the paper so it will feed properly.

For more information about recommended paper, see Recommended paper and print

media in the User's Guide.

Press Go. The machine will print a test page. Check that the test page has

printed correctly.

Note

This function will not be available after the first print job you send from your computer.

Printer LED Indications

Back Cover

Toner

Drum

Paper

Error

Ready

150 mm (6 in.)

150 mm

(6 in.)

Back Cover

Toner

Drum

Paper

Error

Ready

Back Cover

Toner

Drum

Paper

Error

Ready

1 The LED will blink ON and OFF at 1 second intervals.

2 The LED will blink ON and OFF at 0.5 second intervals.

3 The yellow LED will blink in a pattern of ON for 2 seconds and then OFF for 3 seconds.

The machine continues printing until the LED indicates the replace toner message.

Options

The machine has the following optional accessories. You can expand the capabilities of the machine by adding

these items. For more information about the optional Lower Tray Unit and compatible SO‑DIMM Memory, visit us at

http://solutions.brother.com/.

For installing the SO‑DIMM Memory, see Installing extra memory in the User's Guide.

Lower Tray Unit for HL-5440D and HL-5450DN

The lower paper tray unit can hold up to 500 sheets of

paper. When the tray is installed, the machine expands

total input capacity up to 800 sheets.

Consumables

When the time comes to replace consumable items, an error will be indicated by the LEDs on the control panel. For

more information about the consumables for your machine, visit us at http://www.brother.com/original/ or contact

your local Brother reseller.

For replacing the consumable items, see Replacing consumable items in the User's Guide.

Turn the sheet over to install the printer driver.

Quick Setup Guide

HL-5440D

HL-5450DN(T)

Blinking:

ON:

OFF:

Sleep/

Warming Up/

Receiving Data/

OFF

Ready

Deep Sleep

Cooling Down

Data Remaining

Dimmed

Drum End

Toner Low

Replace Toner

Drum Stop

Drum Error

Soon

Front Cover

Back Cover

Service Call

Jam Inside

No Paper

Jam Rear

Open

Error

SO-DIMM Memory (HL-5450DN(T) only)

LT‑5400

You can increase the memory by installing one

SO‑DIMM (Small Outline Dual In‑line Memory

Module).

Toner cartridge

Drum unit