- ページ 5

ソフトウェア Brother MFC490CW - Color Inkjet - All-in-OneのPDF 接続マニュアルをオンラインで閲覧またはダウンロードできます。Brother MFC490CW - Color Inkjet - All-in-One 6 ページ。 Mac network connection
Brother MFC490CW - Color Inkjet - All-in-One にも：クイック・セットアップ・マニュアル (48 ページ), クイック・セットアップ・マニュアル (47 ページ), セットアップとインストール (5 ページ), 修理指示 (2 ページ)

MFC490CW Vista Network Connection Repair Instructions

11. Choose the appropriate key number and press OK:

a. Enter the WEP key you wrote down earlier using the dial pad. You can use the left or right

arrow keys to move the cursor. For example, to enter the letter a, press the 2 key on the dial

pad once. To enter the number 3, press the 3 key on the dial pad seven times. The letters

appear in this order: lower case, upper case, and numbers.

b. Press OK when you have entered all the characters.

Press 1 (YES) to apply your settings. Skip to step 13.

Note: Most access points and routers can store more than one key, but they will only use

one at any time for authentication and encryption.

12. Scroll to TKIP or AES for Encryption Type and press OK.

a. Enter the WPA/WPA2-PSK Password you wrote down earlier using the dial pad. You can use

the left and right arrow keys to move the cursor. For example, to enter the letter a, press the

2 key on the dial pad once. To enter the number 3, press the 3 key on your dial pad seven

times. The letters appear in this order: lower case, upper case, and numbers.

b. Press OK when you have entered all the characters.

Press 1 (YES) to apply your settings.

13. Your machine will now try to connect to your wireless network using the information you have

entered. If successful, CONNECTED will appear on the LCD. A four level indicator at the top of your

machine's LCD will show the wireless signal strength of your access point or router.

If CONNECTION FAILED is displayed then the print server has not successfully connected to your

router or access point. Verify your Network Settings in Step 1 and try connecting from Step 2 again.

If you continue to receive this error, contact your router manufacturer or network admin to verify your

network security settings and that no wireless filters are enabled on the access point.

14. Once the machine is connected the machine will automatically acquire the correct TCP/IP address

information from your access point (router) if DHCP is enabled (DHCP is normally enabled as default

for most access point routers). If DHCP is not enabled, you will have to manually configure the IP

address, subnet mask, and default gateway of the machine to suit your network. Continue to the

steps below to install the drivers on your computer.

PART 8: UNINSTALL AND REINSTALL THE BROTHER DRIVERS

There may be a problem with incomplete, or improper driver installation. To resolve this issue you

may need to uninstall and reinstall the drivers. Please refer to one of the following steps

depending on which type of drivers you originally installed.

1. On the computer click on WINDOWS/START -> (ALL) PROGRAMS -> BROTHER -> XXX-XXXX (Where

X is the model of your Brother machine) -> UNINSTALL. Note: If the software is not installed, Skip to

step 4.

2. When asked to confirm that you want to completely remove the software, click OK.

3. When the uninstall is complete, you will be prompted to restart the computer. Click YES.

4. Once the computer restarts, insert the supplied CD-ROM for Windows into your CD-ROM drive. If

prompted, select your language and model. If the disc does not automatically run, go to

WINDOWS/START -> COMPUTER and double click on the MFL-PRO icon.

5. The CD-ROM main menu will appear.

a. If the software was never installed, or you do not have PaperPort click INSTALL MFL-PRO

SUITE. Continue to Step 6.