- ページ 7

タブレット Fujitsu FPCPR44APのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Fujitsu FPCPR44AP 10 ページ。 Tablet pc tablet dock

ページを印刷する

CONNECTING DEVICES

This section contains instructions on attaching external

peripherals to your Tablet Dock.

To Attach an External VGA Monitor

This option allows you to use an external monitor with

your system. The only requirement is that the external

device (monitor, projector) is a VGA device. Consult the

instructions that come with the device.

1. Securely insert the external monitor plug into the

display port on the back of the Tablet Dock

(Figure 2). Always check the icon by the port before

inserting. Tighten screws if available.

2. You may switch between the internal monitor and

external monitor using the Display Configuration

utility located in the system tray at the bottom right

of the screen, or through the Control Panel settings.

To Attach a USB device

If your Tablet PC supports USB 2.0

devices, the Tablet Dock will also support

USB 2.0 devices.

To attach a USB device, securely insert the connector

into one of the three USB ports on the left side of the

Tablet Dock (Figure 2). It may be necessary to wait a

short time while the appropriate drivers are located and

installed by the system.

To Attach an IEEE 1394 device

The IEEE 1394 interface (also known as "firewire")

allows you to attach IEEE 1394-compliant devices (e.g.,

digital cameras, digital video cameras) to the docked

system.

To attach an IEEE 1394 device, securely insert the

connector into the IEEE 1394 jack on the left side of the

Tablet Dock (Figure 2).

Refer to the device manufacturer's installation and usage

instructions for configuration instructions.

To Attach External Audio Equipment

The Tablet Dock provides a Line Out jack for head-

phones or external speakers.

Connecting external speaker, headphones,

or microphone disables the system's

internal speaker or internal microphone.

To attach an external audio device, insert the plug into

the Line Out jack on the back of the Tablet Dock

(Figure 2).

T a b l e t D o c k U s e r ' s G u i d e

To Attach a LAN Device

The LAN (RJ-45) jack allows you to connect the system's

internal Fast Ethernet to a LAN, or broadband devices

such as a cable modem, DSL, or satellite internet.

Some models of the Stylistic ST Series

Tablet PCs support Gigabit Ethernet. If

your Tablet PC supports Gigabit Ethernet,

the Tablet Dock will also support it.

To attach a LAN device, insert the plug into the LAN

(RJ-45) jack on the back of the Tablet Dock.

Refer to the device manufacturer's installation and usage

instructions for configuration instructions.

USING THE INTERNAL MEDIA DRIVE

The Tablet Dock is outfitted with either a CD-ROM

drive or a DVD/CD-RW Combo drive, depending upon

your dock configuration. A CD-ROM drive allows you

to access software, data, or audio CDs. A DVD/CD-RW

combo drive allows you to access movies, audio, soft-

ware, data, or audio DVD/CDs, and to write data onto

recordable CDs.

CD-ROM drive

All of the software you need to run the CD-ROM drive

is installed in the Tablet PC. The drive will work as

soon as the system is docked and powered up.

Combo DVD/CD-RW drive

Packaged with the Tablet Dock is a CD containing the

applications required to run the DVD and CD/RW

features. The combo drive will only act as a CD-ROM

drive until you install the additional software. To

install the software, refer to instructions on the CD.

The instructions for installing and removing disks is the

same for both drives. For information about the soft-

ware's features and capabilities, refer to the help files

associated with the related applications.

Do not operate your media drive unless

your system is sitting on a relatively flat

surface. Using the drive when the system

is not level may damage the drive or

prevent proper operation.