- ページ 13

食器洗い機 Indesit DPG 15B1のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Indesit DPG 15B1 20 ページ。
Indesit DPG 15B1 にも：取扱説明書 (20 ページ)

ページを印刷する

Rinse aid and refined salt

Only use products which have been specifically designed

for dishwashers.

Do not use table/industrial salt or washing-up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to add

any rinse aid. However, we recommend that you add salt,

especially if you live in an area where the water is hard or

(Follow the instructions given on the packaging).

very hard.

If you do not add salt or rinse aid, the LOW SALT

LOW RINSE AID indicator lights will stay lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water runs off

the surfaces more readily and therefore does not leave streaks

or marks. The rinse aid dispenser should be filled:

• When the LOW RINSE AID indicator light

is illuminated, a reserve supply of rinse aid is still available

for 1-2 cycles;

"D"

1. Open the dispenser

by pressing and pulling up the tab

on the lid;

2. Carefully introduce the rinse aid as far as the maximum

reference notch of the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Rinse-aid quantity setting

If you are not completely satisfied with the drying results, you can

adjust the quantity of rinse aid. Switch the dishwasher on and off

using the ON/OFF button. Press the Start/Pause button 3 times.

Start it using the ON/OFF button. The rinse-aid indicator light will

flash as many times as the level that was set

Adjust the level of rinse aid supply using the SELECT WASH

CYCLE knob.

Press the ON/OFF button to save the setting.

If the rinse aid level is set to ZERO (ECO), no rinse aid will be

supplied. The LOW RINSE AID indicator light will not be lit if you

run out of rinse aid.

Up to maximum 4 levels can be set based on the dishwasher

model.

• If there are streaks on the crockery, set a low number (1-2.)

• If there are drops of water or limescale marks, set a high

number (3-4.)

Setting water hardness

Every dishwasher is equipped with a water softener using refined

salt designed specially for this type of appliance in order to

supply water without limescale for crockery washing.

This dishwasher has a setting that helps reduce pollution and

optimises washing performance in accordance with the water

hardness level in your area. Ask your local water supplier for

this information.

Switch the dishwasher on and off using the ON/OFF button.

Press and hold down the Start/Pause button for a few seconds

until you hear a beep

OFF button. The salt indicator light will flash as many times as

the level that was set

Adjust the hardness level using the SELECT WASH CYCLE knob

(1-2-3-4-5

Press the ON/OFF button to save the setting.

and

Even if using multi-functional tablets, fill the salt dispenser.

Water Hardness Table

level

on the control panel

For values between 0°f and 10°f, we do not recommend the use of salt.

a setting of 5 may increase cycle duration.

(°dH = hardness measured in German degrees - °f = hardness

measured in French degrees – mmol/l = millimoles per litre)

Measuring out the refined salt

In order to obtain the best possible results from a wash cycle,

make sure that the salt dispenser is never empty.

Refined salt removes limescale from the water, thus avoiding

the formation of deposits on crockery.

The salt dispenser is located in the lower part of the dishwasher

(see Description)

• When the green float

• When the LOW RINSE AID indicator light on the control panel

(set to factory level).

little water to leak out.

4. Remove the funnel* and wipe any salt residues away from

the opening; rinse the cap under running water and then screw

it on, the head facing downwards so as to let the water flow out

of the four slots (star-shaped arrangement) in the lower part of

the cap (cap with green float

It is advisable to perform this procedure every time you add

salt to the dispenser.

Make sure the cap is screwed on tightly so that no detergent can

get into the container during the wash cycle (this could damage

the water softener beyond repair).

so that any saline solution which has leaked out of the salt

dispenser is removed.

Only available in selected models.

. Switch the dishwasher on using the ON/

(water softener set to medium level).

see the water hardness table)

°dH

°fH

mmol/l

0 - 6

0 - 10

0 - 1

6 - 11

11 - 20

1,1 - 2

3 12 - 17

21 - 30

2,1 - 3

4 17 - 34

31 - 60

3,1 - 6

34 - 50

61 - 90

6,1 - 9

1 wash cycle per day.

and should be filled:

cannot be seen by simply looking at

the cap of the salt dispenser;

is illuminated

;

1. Remove the lower rack and unscrew

the cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel

fill the salt dispenser up to the edge

(approximately 1 kg). It is normal for a

When necessary, measure out the salt before a wash cycle

up to max. 5 levels.

Average salt dispenser

capacity duration

months

7 months

5 months

3 months

2 months

2/3 weeks

(see figure)

and