- ページ 12

食器洗い機 Indesit IDE 44のPDF 設置および使用マニュアルをオンラインで閲覧またはダウンロードできます。Indesit IDE 44 17 ページ。 Indesit installation and use manual dishwasher ide 44

ページを印刷する

1. Troubleshooting

Cleaning and Special Maintenance

The filter assembly

If you want consistent good results from your dishwasher,

you need to clean the filter assembly; this way the food

particles are removed from the wash water, allowing it to be

recirculated during the cycle, filtered perfectly. For this reason,

it is a good idea to remove the larger food particles trapped

inside the cup "C" and semi-circular filter "A" after each

wash. All you need to do is

rinse them under running

water; to remove these, pull

the cup handle upwards.

The entire filter assembly,

comprising a semi-circular

filter "A", a cup "C", and a

cylindrical filter "B" should

be cleaned thoroughly once

a month. Rotate filter "B"

anticlockwise to remove it. For cleaning, use a non metallic

brush.

Reassemble the three parts as shown in the figures and

reinsert the whole assembly into the dishwasher, positioning

it into its housing and pressing downwards.

Troubleshooting

It may occur that the dishwasher does not function or does not

function properly. Before calling for assistance, let us see what can

be done first: have you forgot to press one of the buttons or to

perform an essential operation?

The Dishwasher Does Not Start

Have you checked whether:

- the plug is pushed into the socket correctly;

- the power is on in the house;

- the door is closed properly;

- the ON-OFF switch is on "ON";

- the water supply is turned on.

The Dishwasher Does Not Load Water

Have you checked whether:

- the water is turned on and the hose is connected properly;

- the water supply to the house is on and has sufficient

pressure;

- the water supply hose is crimped or bent;

- the filter for the water supply hose is clogged.

The Dishes Are Not Clean

Have you put the right amount of detergent into the dispenser?

Is the wash cycle suitable for the dishes you have placed inside the

appliance?

Are the filter and microfilter clean?

Can the sprayer arms turn freely?

The Dishwasher Does Not Drain

Have you checked whether:

- the drain hose is crimped or bent.

Lime Deposits or a White Film Form on the Dishes

Have you checked whether:

- the lid to the salt container is closed properly;

- the rinse aid dosage is correct.

If the display indicates the word "dON" when you turn your

dishwasher on, this means the demo mode is in operation.

Read the instructions on pages 7.

The dishwasher is not to be used without filters. Improper

replacement of the filters may reduce the efficiency of the

wash and even damage your dishwasher.

Cleaning the Sprayer Arms

It may happen that food particle

become encrusted on the

sprayer arms and block the holes

(see "Close up view (interior)",

letters F-I). Check the sprayer

arms periodically and clean them

when needed.

Error messages.

Your dishwasher is equipped with a safety system which is able to

detect any operating anomalies.

These anomalies or faults are signalled by several codes consisting of

letters and numbers that flash up on the display. Make a note of the

error code that appears, turn the appliance off, turn off the water

tap and call for technical assistance.

Tap off alarm

If you have forgotten to turn on the water tap, the appliance will

remind you with a series of prolonged beeps and the wording H2O

will flash up on the display. Turn the tap on and the wash cycle will

start up after a few minutes.

If you are not there when the H2O signal appears, the appliance will

switch to alarm mode and the code "A06" will flash on the display.

Turn the appliance off at button "A", turn on the water tap and wait

approximately 20 seconds before turning the appliance back on, the

wash cycle will start up again.

Clogged filter alarm

If the appliance is blocked and the code "A05" is flashing, this means

the filter is clogged by large particles of food residue. Turn the

appliance off at the ON-OFF button, clean the filter thoroughly and

reposition it in its seat, then turn the appliance back on. The wash

cycle will start up as normal after a few seconds.

Water load solenoid valve malfunction alarm

If the code "A02" flashes, first of all turn off the water tap to avoid

any flooding and then cut off the electricity supply and call for

assistance.

If, despite all these checks, the dishwasher still does not function

and/or the problem persists, contact the nearest authorised service

centre and provide them with the following information:

- the nature of the problem;

- the model type number (Mod. ...) and the serial number (S/N ....),

which are indicated on the plate located on the side of the inner part

of the door.

Never call on unauthorised technicians and refuse to allow

parts to be installed that are not original spare parts.