- ページ 21

オーブン Indesit FIMU 23のPDF 取付・使用説明書をオンラインで閲覧またはダウンロードできます。Indesit FIMU 23 28 ページ。 Electric built under double oven

ページを印刷する

Installation

Electrical Requirements

For your own safety, we recommend that your cooker

is installed by a competent person such as one who

is registered with NICEIC (National Inspection

Council for Electrical Installation Contracting). The

cooker should be installed in accordance with the

latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on

the rating plate corresponds with the house

electricity supply. The cooker must be supplied via

a suitable double pole isolating switch, having a

contact separation of at least 3mm in all poles

placed in a readily accessible position adjacent to

the cooker. If the cooker is to be wired into a

connector unit, this may be positioned behind the

cooker providing the following requirements are met:

i) The connector unit must not project from the wall

more than 25mm.

ii) The top of the connector must not be more than

130mm above floor level.

Remove the terminal cover at the rear base of the

cooker. Pass the cable through the cable clamp and

connect to the appropriate terminals provided.

Allow sufficient cable for any future servicing.

Tighten the screws on the cable clamp and replace

the cover. Make main connections in the connector

unit or cooker control unit. This appliance conforms

to B.S. EN 55014 regarding suppression of Radio

and Television reception interference.

A double Pole control switch having a minimum

rating of 32 amps should be used to feed the cooker

using a suitably rated cable. Where a hob is fitted

adjacent to or over the cooker, a 45 amp Double

Pole control switch should be used to feed both

units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated

twin and earth cable conforming to B.S. 6004 for

connection of each appliance.

In all cases adhere to routing details (see fig. 5).

This appliance must not be installed over any other

appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a

mains cable is not supplied with this product. The

installer will fit the correct type and length of cable.

GENERAL

The appliance is designed to be mounted on a floor

between two adjacent cabinets.

The cabinets must be securely fixed to the wall and

the cooker securely fixed to the cabinets.

This cooker must not be used free standing.

Note; This cooker must not be fitted on a platform.

FINAL INSTALLATION

a. Ensure that the adjacent cabinets and the gap

between them have dimensions in accordance with

the diagram.

b. Assemble the plastic plugs provided into the fixing

brackets. See diagram.

c. Fix the fixing brackets to the sides of the adjacent

cabinets so that the centre line of the brackets are

570mm above the top of the plinth line and the front

face of the plastic plug is level with the front face

of the cabinet sides. See diagram.

d. Adjust the feet on the cooker to their minimum

position, i.e. fully screwed in.

e. Slide the cooker centrally into the space between

the cabinets ensuring the following:

i) The gap between the cabinet sides and the

cooker is even along the length of the cabinet

sides.

ii) The cable is routed away from any vents in the

rear panel and is not trapped between the cooker

and the wall, adjacent cabinets or under the feet

f. Adjust the feet using an open ended spanner until

the bottom of the cooker door is in line with the top

of the plinth. Using a spirit level, check that the

cooker is level in all directions.

g. Check that the plinth can be fitted. If necessary re

- adjust the feet and check that the cooker is level.

Then lock the feet into position by tightening the

lock nut using an open ended spanner.

h. Open the top oven door and fix the cooker to the

brackets through the holes in the side trims.

i. Fix the plinth in position.

j. Ensure that there is a minimum gap of 1mm

between the cooker side trim and the adjacent

cabinet doors or drawer fronts.

k. If a hob is to be installed directly above the cooker

it must not project downwards more than 20mm

below the underside of the work top. Any projection

of more than 10mm must not project more than

500mm from the wall.

Fig. 5