- ページ 18

調理器 Indesit 6G25S/UのPDF 設置および使用マニュアルをオンラインで閲覧またはダウンロードできます。Indesit 6G25S/U 28 ページ。

ページを印刷する

cabinet is a minimum of 420 mm. above the worktop.

The minimum distance combustible material kitchen

units can be fitted directly above the worktop is 700

mm.

e) The wall in contact with the back of the cooker must

be of flameproof material.

Min.

Connecting the gas

The appliance should be connected to the mains or to a

gas cylinder in compliance with current directives. Before

making the connection, check that the cooker is regulated

for the gas supply you are using. If not, follow the

instructions indicated in the paragraph "Adapting to

different types of gas". On some models the gas supply

can be connected on the left or on the right, as necessary;

to change the connection, reverse the position of the hose

holder with that of the cap and replace replace the gasket

(supplied with the appliance). When using liquid gas from

a cylinder, install a pressure regulator which complies with

current directive.

Important: check that the supply pressure complies with

the values indicated in table 1 "Characteristics of the

burners and nozzles" since this will ensure safe operation,

correct consumption and ensure a longer life to your

appliance.

Connection with a Hose

Make the connection using a gas hose that complies with

requirements set forth by the current National Regulations.

When installing the hose, remember to take the following

precautions:

•

No part of the hose should touch parts whose tem-

perature exceeds 50°C;

•

The length of the hose should be less than 1500 mm;

•

The hose should not be subject to twisting or pulling,

and should not have bends or kinks.

•

The hose should not touch objects with sharp edges,

moving parts, and it should not be crushed;

•

The full length of the hose should be easy to inspect in

order to check its condition.

Check that the hose fits firmly into place at the two ends

and fix it with clamps complying with current National Regu-

lations. If any of the above recommendations can not be

followed, flexible metal pipes should be used. If the cooker

is installed in compliance with the requirements for class

2, subclass 1, it is highly recommended that the gas con-

nection be made with a flexible metal pipe in compliance

with current safety standards.

Connecting a Flexible, Jointless, Stainless Steel Pipe

to a Threaded Attachment

The hose holder fitted on the appliance. The gas supply

pipe fitting is a threaded 1/2 gas conic male attachment.

HOOD

600

mm.

Only use pipes and gaskets complying with current Na-

tional Regulations. The full length of the pipe must not

exceed 2000 mm. Once the connection has been made,

ensure that the flexible metal pipe does not touch any

moving parts and is not crushed. Once the connection

has been made, ensure that the flexible metal pipe does

not touch any moving parts and is not crushed.

Checking that the Connection is Tight

Important: When installation has been completed, check

the pipe fittings for leaks using a soapy solution. Never

use a flame.

Connecting the supply cable to the mains

Install a normalised plug corresponding to the load

indicated on the data plate. When connecting the cable

directly to the mains, install an omnipolar circuit-breaker

with a minimum contact opening of 3 mm between the

appliance and the mains. The omnipolar circuit breaker

should be sized according to the load and should comply

with current regulations (the earth wire should not be

interrupted by the circuit breaker).

The supply cable should be positioned so that it does not

reach a temperature of more than 50°C with respect to

the room temperature, along its length. Before making the

connection, check that:

•

the limiter valve and the home system can support the

appliance load (see data plate);

•

the mains is properly earthed in compliance with

current directives and regulations;

•

there is easy access to the socket and omnipolar circuit

breaker, once the hob has been installed.

N.B: never use reducers, adaptors or shunts since they

can cause heating or burning.

Adapting the cooker to different types of gas

In order to adapt the cooker to a different type of gas with

respect to the gas for which it was produced (indicated on

the label attached to the lid), follow these steps:

a) Replacing the burner nozzles on the hob:

•

remove the grids and slide the burners from their

housings;

•

unscrew the nozzles using a 7 mm socket spanner,

and replace them with nozzles for the new type of gas

(see table 1 "Burner and nozzle characteristics").

•

replace all the components by repeating the steps in

reverse order.

b) Minimum regulation of the hob burners:

•

turn the tap to minimum;

•

remove the knob and adjust the regulation screw, which

is positioned in or next to the tap pin, until the flame is