- ページ 6

調理器 Indesit ITL50GMのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Indesit ITL50GM 24 ページ。 Indesit it50g s; it50g1 s; it50l s; it50g1; it50l; it50g; itl50g1; itl50gm; itl50ga; itl50gw 50cm free standing gas cooker

ページを印刷する

Brown - Live

If the colours of the wires in the mains lead do not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked "E" or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked "L" or coloured

Red.

Connect Blue wire to terminal marked "N" or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a 13 amp fuse. A 15 amp plug must be protected

by a 15 amp fuse, either in the plug or adaptor or at

the distribution board. If you are in any doubt about the

electrical supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE

"NEUTRAL" ("N")

BROWN "LIVE" ("L")

GREEN AND YELLOW

Disposing of the appliance

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible to

the plug body and dispose of it as described above.

GREEN &

YELLOW

13 amp fuse

BROWN

CROSS-BAR

BLUE

CORD GRIP

a) replace the hose holder mounted on the

appliance with that supplied in the bag of "cooker

accessories".

b) Replacing the burner nozzles on the hob:

• remove the grids and slide the burners from their

housings;

• unscrew the nozzles using a 7 mm socket

spanner, and replace them with nozzles for the

new type of gas (see table 1 "Burner and nozzle

characteristics").

• replace all the components by repeating the steps in

reverse order.

"EARTH" ("E")

Adapting the cooker to

different types of gas

In order to adapt the cooker

to a different type of gas with

respect to the gas for which it

was produced (indicated on the

label attached to the lid), follow

these steps:

c) Minimum regulation of the hob burners:

• turn the tap to minimum;

• remove the knob and adjust the regulation screw,

which is positioned in or next to the tap pin, until the

flame is small but steady.

! in the case of liquid gas, the regulation screw must

be screwed in to the bottom.

• check that the flame does not

turn off when you turn the tap

quickly from high to low.

primary air of the burners:

The primary air of the burners

requires no regulation.

Adapting to different types of gas

In order to adapt the oven to

a different type of gas with

respect to the gas for which it

was manufactured (indicated

on the label), follow these

simple steps:

a) Replacing the oven burner

nozzle

• open the oven door fully

• pull out the sliding oven bottom

unscrew the two screws and take off the shield

protecting the burner (in main oven burner only).

• Pry the fixing tab "V" and remove the oven burner

• Unscrew the oven burner nozzle using the socket

spanner for the nozzles "Z", or a 7 mm socket

spanner, and replace it with a nozzle suited to the

new type of gas (see Table 1).

Take particular care handling the spark plug wires

and the thermocouple pipes.

• Replace all the parts, following the steps described

above in the reverse order.

b) Minimum regulation of the gas oven burner with

thermostat:

• light the burner as described in the paragraph "the

oven knob" of the instruction booklet.

Regulating the