- ページ 5

調理器 Indesit K 3G21/GのPDF 取付・使用説明書をオンラインで閲覧またはダウンロードできます。Indesit K 3G21/G 17 ページ。 Indesit cookers operating instructions
Indesit K 3G21/G にも：取付・使用説明書 (17 ページ), 取扱説明書 (12 ページ), 取扱説明書 (12 ページ)

ページを印刷する

HOT PARTS

Important: make sure the supply pressure conforms with

the values shown in the table entitled "Caracteristics of the

burners and nozzles". When the cooker is installed

between cabinets (recessed), the gas connection must

be effected by an approved flexible hose with bayonet

fitting (BS 669 Current Edition). The gas inlet for the

cookers is a threaded G 1/2 gas female fitting.

Connecting the gas supply

To make the connection, a flexible hose should be used

corresponding to the current gas regulations which are:

•

the hose must never be at any point in its lenght in contact

with the "hot" parts of the cooker;

the hose must never be longer than 1,5 metre;

•

the hose must not be subject to any tension or torsional

stress and it must not have any excessively narrow curves

or bottlenecks;

the hose must be easy to inspect along its entire length

•

to check its condition;

•

the hose must always be in good condition, never attempt

to repair.

Important: the installation must comply with gas safety

(installation and use) regulations 1984. In all cases for the

above, by low, a qualified, corgi approved engineer must be

called for installation.

Electrial connection

Power supply voltage and frequency: 230-240V a.c. 50/60 Hz.

Note: the supply cable must be positioned so that it never

reaches at any point a temperature 50°C higher than the

room temperature. The cable must be routed away from the

rear vents. Should you require it, you may use a longer cable,

however, you must ensure that the cable supplied with the

appliance is replaced by one of the same specifications in

accordance with current standards and legislation.

Your appliance is supplied with a 13 amp fused plug that can

be plugged into a 13 amp socket for immediate use. Before

using the appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved fuse

to BS 1362 should always be used, and the fuse cover re-

fitted. If the fuse cover is lost, the plug must not be used until

a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the correct

colour as indicated by the coloured marking or the colour

that is embossed in words on the base of the plug.

Replacements can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and

you should wish to remove it to add a cable extension or to

re-route the mains cable through partitions, units etc., please

ensure that either:

•

the plug is replaced by a fused 13 amp re-wireable plug

bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable outlet,

•

controlled by a switch, (in compliance with BS 5733) which

is accessible without moving the appliance.

Please note: for appliances with a rating greater than 13

amp (eg: electric hob, double ovens and freestanding electric

cookers etc.) the mains cable must be wired into a cooker

output point with a rating of 45 amp. In this case the cable is

not supplied.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make the

pins unusable so that it cannot be accidentally inserted into

a socket. Instructions for connecting cable to an alternative

plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow

Blue

Brown

If the colours of the wires in the mains lead do not correspond

with the coloured markings identifying the terminals in your

plug, proceed as follows:

Connect Green & Yellow wire to terminal marked "E" or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked "L" or coloured Red.

Connect Blue wire to terminal marked "N" or coloured Black.

If a 13 amp plug (BS 1363) is used it must be fitted with a 13

amp fuse. A 15 amp plug must be protected by a 15 amp

fuse, either in the plug or adaptor or at the distribution board.

If you are in any doubt about the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance with

the following code:

BLUE

BROWN

GREEN AND YELLOW

GREEN &

YELLOW

BROWN

BLUE

Disposing of the appliance

When disposing of the appliance please remove the plug by

cutting the mains cable as close as possible to the plug body

and dispose of it as described above.

- Earth

- Neutral

- Live

"NEUTRAL" ("N")

"LIVE" ("L")

"EARTH" ("E")

13 amp fuse

CROSS-BAR

CORD GRIP