- ページ 14

洗濯機／乾燥機 Indesit BIWDIL7125のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Indesit BIWDIL7125 15 ページ。
Indesit BIWDIL7125 にも：クイックマニュアル (4 ページ)

ページを印刷する

Using the Drilling Template.

- To trace the positions of the holes on the left-

hand side of the panel, align the drilling template

to the top left side of the panel using the lines

traced on the extremities as a reference.

- To trace the positions of the holes on the right-

hand side of the panel, align the drilling template

to the top right side of the panel.

- Use an appropriately sized router to mill the holes

for the two hinges, the rubber plug and the magnet.

Mounding the Parts onto the Wooden Panel (Door).

- Insert the hinges into the holes (the movable part

of the hinge must be positioned facing away from

the panel) and fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the

opposite side of the hinges and fasten it with the

two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the

machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow

in fig. 2) into the hole for the hinge and push the

panel towards the front of the machine. Fasten

the two hinges with the type D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of

modular cabinets, mount either one or both of the

guides for the base molding (as shown in fig. 8).

Adjust them for depth based on the position of

the base molding, and, if necessary, fasten the

base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide Q

into the special slot and once it is in the desired

position, lock it in place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it

with the cabinets (fig. 6).

- Regulate the adjustable feet to raise the machine

to the appropriate height.

- To adjust the position of the wooden panel in

both the vertical and horizontal directions, use the

C and D screws, as shown in fig. 7.

Important: close the lower part of the appliance front

by ensuring that the plinth rests against the floor.

Fig. 6

Fig. 7

Fig. 8

Accessories provided for the height adjustment.

Fig. 10

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from

815 mm to 835 mm), by turning the 4 feet.

Should you require the appliance to be placed

higher than the above height, you need to use the

following accessories to raise it to up to 870 mm:

the two crossbars (G); the 4 feet (H); the 4 screws

(I); the 4 nuts (L) then perform the following

operations (fig. 11):

remove the 4 original feet, place a crossbar G at

the front of the appliance, fastening it in place

using screws I (screwing them in where the original

feet were) then insert the new feet H.

Repeat the same operation at the back of the

appliance.

Now adjust feet H to raise or lower the appliance

from 835 mm to 870 mm.

Once you have reached the desired height, lock

nuts L onto crossbar G.

To adjust the appliance to a height between 870

mm and 900 mm, you need to mount strip M,

adjusting feet H to the required height.

Insert the strip as follows:

loosen the three screws N situated at the front of

the Top cover of the appliance, insert strip M as

shown in fig. 12, then fasten screws N.

Fig. 11

Fig. 9

The following can be found

inside the polystyrene lid (fig.

10): 2 crossbars (G), 1 strip

(M)

the following can be found

inside the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

Fig. 12

11338876