- ページ 3

洗濯機／乾燥機 Indesit IWDE 7168のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Indesit IWDE 7168 16 ページ。 Washer-dryer
Indesit IWDE 7168 にも：取扱説明書 (16 ページ), 取扱説明書 (16 ページ), 取扱説明書 (16 ページ)

ページを印刷する

Connecting the drain hose

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

! We advise against the use of hose exten-

sions; in case of absolute need, the exten-

sion must have the same diameter as the

original hose and must not exceed 150 cm in

length.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed

down too far, this may cause the machine to self

-syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance

with the applicable law;

• the socket is able to sustain the applian-

ce's maximum power load indicated in the

Technical details table (see page 5);

• the supply voltage is included within the

values indicated on the Technical details

table (see page 5);

Connect the drain

hose, without ben-

ding it, to a draining

duct or a wall drain

situated between 65

and 100 cm from

the floor;

The drain hose may

be connected to

an under-sink trap.

Before connecting

the drain hose from

the machine ensu-

re that any blanks

or removable ends

have been taken off

the spigot.

If it is place over

the edge of a basin

or sink be sure the

free end of the hose

should not be un-

derwater.

• the socket is compatible with the washing

machine's plug. If this is not the case, repla-

ce the socket or the plug.

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD

BE CARRIED OUT BY A QUALIFIED ELECTRI-

CIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be

of the correct colour as indicated by the colou-

red marking or the colour that is embossed in

words on the base of the plug. Replacements

can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moul-

ded plug and you should wish to re-route the

mains cable through partitions, units etc.,

please ensure that either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Instructions for connecting cable to an alterna-

tive plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow

Earth

Blue

Neutral

Brown

Live