- ページ 2

バスルーム設備 Kohler Centerpiece K-2264のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Kohler Centerpiece K-2264 16 ページ。 Countertop and undercounter lavatories
Kohler Centerpiece K-2264 にも：ホームオーナーズマニュアル (16 ページ), ホームオーナーズマニュアル (24 ページ)

ページを印刷する

LOCATING THE FAUCET CENTERLINE

This lavatory is a unique installation with the faucet fittings mounted

on the countertop rather than on the lavatory itself.

The best location of the faucet centerline is determined by three

items: the size of the fitting or faucet spout escutcheons, length of

faucet spout, and clearance between the faucet spout and lavatory

rim.

FAUCET LOCATION

Refer to Fig. #1 . Determine if the faucet spout escutcheon or

faucet handle escutcheon will be closer to the lavatory rim

when installed. Items to consider are the sizes of the different

faucet components and the lavatory shape. The escutcheon

found to be closest to the lavatory rim will be used in step 2.

Faucet Handle Escutcheon

Faucet Spout Escutcheon

Measure the escutcheon, front-to-back, that was found to be

closest to the rim in step 1. This escutcheon measurement

may also be found on the faucet roughing-in page.

Divide the front-to-back dimension in half, and add 1/4".

Standard sizes are shown in the chart on the next page. The

distance found will be used to draw the preliminary faucet

centerline.

NOTE: For all front to back dimensions, round up to the nearest

1/16" (2mm) if required.

FRONT TO

DISTANCE TO DRAW CENTERLINE

BACK DIMENSION

BEHIND REFERENCE LINE

2" (5cm)

1-1/4" (3.2cm)

2-1/8" (5.4cm)

1-5/16" (3.3cm)

2-1/4" (5.7cm)

1-3/8" (3.5cm)

2-3/8" (6cm)

1-7/16" (3.7cm)

2-1/2" (6.4cm)

1-1/2" (3.8cm)

1007251-2-

Lavatory Rim

Fig. #1

DRAW PRELIMINARY FAUCET CENTERLINE

NOTE: The following instructions refer to the installation of

Model K ---2332, in an above counter installation.

NOTE: Wall-mount faucet installations: Be sure to provide

sufficient spout overhang into the lavatory basin. Make sure that

the water stream is directed to the center of the lavatory and

there is sufficient hand washing clearance.

NOTE: Countertop faucet installations: Pay special attention

to the spout and handle fit clearance when locating the faucet, as

noted below.

Countertop faucet installations: Use the template to locate the

faucet spout hole centerline to provide adequate clearance between

the edge of the lavatory and the spout.

Refer to Fig. #2 . Check for adequate clearance between the back-

splash, faucet spout and handles and lavatory. Kohler recommends

clearance of at least 1" (2.5cm) between:

the installed lavatory and the faucet spout;

the installed lavatory and the end of the faucet handles

the faucet spout and handles, and the backsplash.

Refer to the faucet installation instructions for the required

clearance, and mark the preferred faucet hole locations.

Spout

Centerline

Backsplash

Cut-out

Line

Fig. #2

;

1"(2.5cm)

Minimum

Clearance

Outside Edge

of Lavatory

1-1/4"(3.2cm)

Minimum

Clearance

Kohler Co.