- ページ 5

エンジン Kohler COMMAND PRO CS10のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Kohler COMMAND PRO CS10 21 ページ。 Horizontal crankshaft
Kohler COMMAND PRO CS10 にも：オーナーズマニュアル (20 ページ), オーナーズマニュアル (20 ページ)

ページを印刷する

Fuel Recommendations

WARNING: Explosive Fuel!

Gasoline is extremely flammable and its vapors can

explode if ignited. Store gasoline only in approved

containers, in well ventilated, unoccupied buildings,

away from sparks or flames. Do not fill the fuel tank

while the engine is hot or running, since spilled fuel

could ignite if it comes in contact with hot parts or

sparks from ignition. Do not start the engine near spilled

fuel. Never use gasoline as a cleaning agent.

General Recommendations

Purchase gasoline in small quantities and store in

clean, approved containers. A container with a capacity

of 2 gallons or less with a pouring spout is

recommended. Such a container is easier to handle

and helps eliminate spillage during refueling.

Do not use gasoline left over from the previous season,

to minimize gum deposits in your fuel system and to

ensure easy starting.

Do not add oil to the gasoline.

Do not overfill the fuel tank. Leave room for the fuel to

expand.

Fuel Type

For best results use only clean, fresh, unleaded

gasoline with a pump sticker octane rating of 87 or

higher. In countries using the Research method, it

should be 90 octane minimum.

Unleaded gasoline is recommended as it leaves less

combustion chamber deposits. Leaded gasoline may be

used in areas where unleaded is not available and

exhaust emissions are not regulated. Be aware

however, that the cylinder head will require more

frequent service.

Gasoline/Alcohol blends

Gasohol (up to 10% ethyl alcohol, 90% unleaded

gasoline by volume) is approved as a fuel for Kohler

engines. Other gasoline/alcohol blends are not

approved.

Gasoline/Ether blends

Methyl Tertiary Butyl Ether (MTBE) and unleaded

gasoline blends (up to a maximum of 15% MTBE by

volume) are approved as a fuel for Kohler engines.

Other gasoline/ether blends are not approved.

Engine Identification Numbers

When ordering parts, or in any communication involving

an engine, always give the Model, Specification, and

Serial Numbers of the engine.

The engine identification numbers appear on a decal

(or decals) affixed to the engine shrouding. Include

letter suffixes, if there are any.

Record your engine identification numbers on the

identification label below (Figure 4) for future reference.

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PHASE II, 2002-2005

CALIFORNIA AND EC STAGE II (SN:4) EMISSION

CONTROL REGS FOR SI SMALL OFF–ROAD

ENGINES

FAMILY

TYPE APP

MODEL NO.

SPEC. NO.

DISPL. (CC)

SERIAL NO.

OEM PROD. NO.

EMISSION COMPLIANCE PERIOD:

EPA: CATEGORY A

CERTIFIED ON: UNLEADED GASOLINE

REFER TO OWNER'S MANUAL FOR SAFETY,

MAINTENANCE SPECS, AND ADJUSTMENTS

1-800-544-2444 www.kohlerengines.com

KOHLER CO. KOHLER, WISCONSIN USA

(REF:_______________ )

Figure 4. Engine Identification Label.

The Emission Compliance Period referred to on the

Emission Control or Air Index label indicates the

number of operating hours for which the engine has

been shown to meet Federal and CARB emission

requirements. The following table provides the Engine

Complicance Period (in hours) associated with the

category descriptor found on the certification label.

Emission Compliance Period (Hours)

Category C

EPA

250 Hours

Moderate

CARB

125 Hours

Refer to certification label for engine displacement.

Exhaust Emission Control System for models

CS4-12.75 is EM.

N432

Category A

Category B

1000 Hours

500 Hours

Intermediate

Extended

250 Hours

500 Hours