- ページ 6

キッチン家電 A.J.Antunes roundup MS-150のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。A.J.Antunes roundup MS-150 16 ページ。 Miracle steamer

ページを印刷する

READY

SINGLE SHOT

DOWN

PRGM

START/STOP

POWER

Figure 4. operating Controls

operaTinG inSTrucTionS

1. Turn the power on and allow the unit

to preheat for approximately 20-30

minutes.

NotE: Do Not push any button dur-

ing warmup time. the flashing green

ready Light indicates that the unit is not

warmed up. the ready Light will become

steady when the unit is warmed up.

2. Pull out the Spatula and set the prod-

uct to be steamed onto the Spatula.

3. Push the Spatula fully into the

steamer.

4. Single Shot: Press and release the

Operate button, then wait 20 seconds

for the steam to penetrate the product.

timed Cycle: Press the Start/Stop

button to begin the steaming cycle.

The display will count down to zero

and an audio signal will sound at the

end of the steaming cycle.

5. Remove steamed product.

WarNING

To avoid injury, be careful when pulling the

spatula out from the unit. Be sure to allow

steam to escape before putting hands or

face over the steamer.

proGraMMinG

ready

CYC (total Cycle time) refers to the total

Light

programmed steam time set for the product.

SHo (Shot Interval time) refers to the time set

Message

between shots of steam during a complete cycle.

Display

H2o setting (Steam Shot time) refers to the

Start/Stop

water volume consumed during each water

Button

pump activation.

operate

The amount of steam produced by your

Button

Miracle Steamer depends on the amount of

power

water sprayed onto the steam generator.

Switch

Flooding of the generator may occur if the

H2O setting is too high. To prevent flooding,

the Shot Interval Time (SHO) can be increased

to allow more time for generator heat recov-

ery. Adjustments should be made to both

values to determine the best settings for your

cooking needs.

1. Turn the unit on. The unit displays the

factory programmed Total Cycle Time

in minutes and seconds.

2. Press and release

control from OPERATION to PROGRAM

mode.

3. To change the Total Cycle Time in

minutes, press ▲ or ▼ to change the

time.

4. Press and release

▲ or ▼ to change the Total Cycle

Time in seconds.

5. To change the SHO factory settings,

make sure the control is in PROGRAM

mode, then press and hold both ▲

and ▼ simultaneously for 1-2 seconds

and release. "SHO" will be displayed.

6. Press and release

▲ or ▼ to change the SHO in seconds.

7. Press and release

▲ or ▼ to change the SHO in minutes.

8. Press and release

"H2O" will be displayed.

9. To change the H2O (Steam Shot time),

press and release the Program button

again to display the setting. Use▲ or

▼ to increase or decrease the time.

10. Press the Start/Stop or Operate but-

tons to store the changes, exit the

PROGRAM Mode, and initiate the

cooking cycle.

IMportaNt: Miracle Steamers are factory

programmed for the following recom-

mended settings:

NotE: the Start/Stop or operate buttons

may be pressed at any time during pro-

gramming to store the changes and exit

the proGraM Mode.

NotE: If a change is not made within 5

seconds at any time during the program-

ming process, all changes made up to that

point are stored in memory and the con-

trol reverts to the opEratIoN Mode.

to change the

again, and press

and then press

again and press

again and

• Total Cycle Time (CYC) = 15 min., 00

secs. (Range: 3 seconds to 99 minutes

59 seconds)

• Shot Interval Time (SHO) = 00 min., 20

secs. (Range: 3 seconds to 5 minutes

59 seconds)

• Steam Shot Time (H2O) = 1_00

(Range: 0_10 second to 2_50)

P/N 1010881 Rev. F 03/12