- ページ 5

リモコン CPI MCR220のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。CPI MCR220 14 ページ。 Mcr / tsr series multi-channel remote controls

ページを印刷する

Channel / System display: The LED display gives a

real-time indication as to what channel / system the radio

is on. All parallel remote displays and the radio display

update simultaneously.

Scan indicator: When scan is selected by pressing the

scan button on the remote or the radio, the scan LED will

illuminate and/or the appropriate horizontal bars will be

displayed on the remote. Note: Some radios do not

support the scan LED.

Monitor indicator: Operates the same as radio.

Transmit indicator: Illuminates when any remote has

keyed or the local microphone has been keyed. This

indicator does not flash when a channel is busy.

Channel Up / System: Pushed once, it will increment

the selected channel / system by one. If held, will con-

tinue to increment until released.

Channel Down / Group / Subfleet: Pushed once, it will

decrement the selected channel / group /subfleet by one.

If held, will continue to decrement until released.

Scan button: Toggles the radio scan function.

Monitor button: Toggles the radio monitor function.

PTT button (front panel): Allows telephone style units

to transmit without lifting the handset using the panel

microphone. On console style units it functions the same

as the desk mic PTT.

PTT button (handset): Off-hook it allows telephone

style units to transmit with handset.

Intercom switch: Provides intercom capability between

parallel remotes or the radio. Can be used by depressing

switch and speaking into panel or desk microphone. On

the telephone style units it can be used off-hook by

depressing button and speaking into handset micro-

phone.

To intercom between the radio and a remote, press and

hold the intercom switch on the termination panel and

speak into the local microphone while keying it.

Parallel operation

Up to 50 MCR /TSR series remote units may be con-

nected in parallel.

As parallel units are installed, the setup procedure need

only be performed on the new remote(s). The existing

remotes do not require readjustment.

Motorola Trunking

Since remote operation with Motorola Trunking has some

unique requirements, more detail follows.

Most of the remotes operating feature are the same as

the radio and therefore only the differences will be

described here.

TRANSMITTING ON A TRUNKED SYSTEM: The

remote's transmit LED will always light steady when PTT,

handset or front panel, is depressed. You therefore must

listen for the high-pitched "di-di-dit" talk permit tone to let

you know it is OK to transmit.

Other tones such as the talk prohibit tone or the busy

tone may be heard depending on system status. Refer

to your radio's operating instructions for explanations of

these tones. These tones will not be heard when trans-

mitting on-hook, they will only be heard when using the

handset.

TRANSMITTING ON A CONVENTIONAL SYSTEM:

The remote's transmit LED will always light steady when

PTT, Handset or front panel, is depressed. You there-

fore must listen for the high-pitched "di-di-dit" talk permit

tone to let you know it is OK to transmit. Do not transmit

if some else is using the channel. These tones will not be

heard when transmitting on-hook, they will only be heard

when using the handset.

CALL ALERT ®: When a Call Alert is received, the

amber call LED will light steady and you will hear the

four tones over the remote's speaker and handset

earpiece. The display will not show "CA". You will

continue to hear the alert tones and the call LED will stay

lit until a PTT or system change is made.

Sending a Call Alert is done much the same as the on

the radio, with some minor deferences. There will be no

call LED activity, you must listen for the single beep to

indicate the call alert has been sent. When the Call Alert

is acknowledged you will hear the four beeps but there

will be no call LED activity on the remote.

TELEPHONE INTERCONNECT OPERATION: Not

supported from the remote.

SCAN LIST: Programming or altering the scan list can

not be done from the remote. It must be done from the

radio.

NUISANCE DELETE SCAN FEATURE: Not supported

from the remotes.