- ページ 11

グラインダー DGP DGP-PG3-V2のPDF 操作マニュアルをオンラインで閲覧またはダウンロードできます。DGP DGP-PG3-V2 13 ページ。 Tungsten grinder

ページを印刷する

1. Parts List

10. VACUUM SYSTEM OVERVIEW

The DGP-PG3-V2 comes with a tool cabinet and integrated vacuum system for the collection of tungsten

10. VACUUM SYSTEM OVERVIEW

dust. This feature has become very popular due to the disclosures in the past few years about the danger of

1 0. VACUUM SYSTEM OVERVIEW

inhaling dust from the commonly used 2% Thoriated tungsten. This danger is because 2% Thoriated tungsten

The DGP-PG3-V2 comes with a tool cabinet and integrated vacuum system for the collection of tungsten

is radioactive and is a known cancer causing element. Please contact your local OSHA office if you would like

dust. This feature has become very popular due to the disclosures in the past few years about the danger of

more information about this issue. In addition, we offer free samples of non-radioactive alternative tungsten,

inhaling dust from the commonly used 2% Thoriated tungsten. This danger is because 2% Thoriated tungsten

which performs better in most applications.

is radioactive and is a known cancer causing element. Please contact your local OSHA office if you would like

more information about this issue. In addition, we offer free samples of non-radioactive alternative tungsten,

It is impossible to contain all of the lightweight dust particles that deflect quickly off the wheels from grinding.

which performs better in most applications.

The vacuum system offers a way of collecting the majority of the dust that is produced while grinding and

cutting tungsten electrodes. Replacement vacuum filters are in stock at the factory and ready for immediate

It is impossible to contain all of the lightweight dust particles that deflect quickly off the wheels from grinding.

shipment. Installation instructions come with replacment filters. Filter replacement is a very quick and easy

The vacuum system offers a way of collecting the majority of the dust that is produced while grinding and

process.

cutting tungsten electrodes. Replacement vacuum filters are in stock at the factory and ready for immediate

shipment. Installation instructions come with replacment filters. Filter replacement is a very quick and easy

process.

SYMPTOMS

Grinder won't start

Excessive vibration

Grooved wheel

Motor is overheating

Document: DGP-MANUAL-P3-V2 | DGP-PG3-V2 Product User Manual | Released: 7/11 Rev. C

TROUBLESHOOTING CHART

POSSIBLE CAUSE(S)

TROUBLESHOOTING CHART

POSSIBLE CAUSE(S)

1. Blown line or tripped circuit breaker

2. Low line voltage

3. Material wedged between wheel & guard

1. Improper mounting of grinder or accessories

2. Improper wheel mounting

1. Electrode pushed with excessive force.

2. On steep angled tungsten,

collet touching wheel

1. Motor not turning freely (without power)

CORRECTIVE ACTION

1. If fuse is blown, replace

2. If voltage is less than rated,

3. Remove material wedged

1. Remount

2. Remount wheels but rotate one

1. Use recommended grinding

2. Use short collets availabe from

1. Clean around wheels & shaft.

Page 11

2091 Las Palmas Drive, Ste. F

Page 11

Carlsbad, CA 92011 - Tel. 1.760.931.1500

Email: [email protected]

CORRECTIVE ACTION

1. If fuse is blown, replace

with fuse of proper size.

If breaker is tripped reset it.

with fuse of proper size.

If breaker is tripped reset it.

2. If voltage is less than rated,

check size of wiring from

main switch on property. If

check size of wiring from

OK, contact power company.

main switch on property. If

OK, contact power company.

3. Remove material wedged

between wheel and guard.

1. Remount

2. Remount wheels but rotate one

wheel 1/4 turn with respect to its

previous position. Other wheel

would retain its original position.

1. Use recommended grinding

times table

2. Use short collets availabe from

Diamond Ground Products.

1. Clean around wheels & shaft.

Then replace bearing.

Arc-Zone.com, Inc.

11 / 13