- ページ 19

モニター Dell D1626HT - UltraScan 1600HS - 21" CRT DisplayのPDF サービスマニュアルをオンラインで閲覧またはダウンロードできます。Dell D1626HT - UltraScan 1600HS - 21" CRT Display 48 ページ。 Color monitor
Dell D1626HT - UltraScan 1600HS - 21" CRT Display にも：サービスマニュアル (48 ページ)

ページを印刷する

Landing Rough Adjustment

1. Enter the full white signal. (or the full black dots signal).

2. Adjust the contrast to the maximum.

3. Make the screen monogreen.

Note: Off the outputs from R ch and B ch of SG.

4. Reverse the DY, and adjust coarsely the purity magnet so that

a green raster positions in the center of screen.

5. Adjust the tilt of DY, and fix lightly with a clamp.

Note: "TILT" shall be set at 0.

Landing Fine Adjustment

1. Put the set inside the Helmholtz coil. ("LCC SW" = "12")

2. Input the single green signal and set the CONT control to

MAX.

Note: After the W/B adjustment with 9300K, measure an average

of Ik when a full white signal is entered in the CONT

MAX/BRT CENT status. Then make adjustment so that the

specified screen can be attained after aging for 2 hours with

Ik equivalent to 30% of the average value.

3. Demagnetize the metal part of the chassis with the hand de-

gausser and coil degausser, and the CRT surface with the

hand degausser.

Input AC 230V to AC IN, turn on and off the power to per-

form auto degaussing. (Perform auto degaussing by setting

"MON CON REG2"=152. Return to the original value after

use.)

Demagnetize the CRT surface with the hand degausser again.

Note:

(1) Hand degauss must be used on stand-by or power-off condi-

tion.

This model has an automatic earth magnetism correction

function by using an earth magnetism sensor and a LCC coil.

When using a hand degauss while monitor (LCC coil) is being

operated, it sometimes gets magnetized, and the system may

not work properly as a result.

(2) Adjust in a non-magnetic field. BV=45uT.

(3) If adjusting in a magnetic fields, add the shift from the non-

magnetic field in your estimation.

4. Attach the wobbling coil to the designated part of the CRT

neck.

5. Attach the sensor of the landing adjustment unit on the CRT

surface.

6. Adjust the DY position and purity, and the DY tilt, and land-

ing of the center and 4 corners with the landing checker.

After adjustment, set "LCC SW" to "13".

Write terrestrial magnetism sensor reading VX and VY to

"LCC VX" and LCC VY" respectively. Adjust the landing

by moving "LCC NS", "LCC LT", "LCC LB", "LCC RT"

and "LCC RB". However, the register adjustment must be

limited within the following range.

"LCC NS"

"LCC LT", "LCC LB", "LCC RT", "LCC RB"

Save the service data.

ADJUSTMENTS

Adjust so that the green is within

the specification given right.

4 corner adjust target : within ± 1

The red and blue must be within

the specification given right with

respect to the green.

A difference between red and blue

must be within the specification

given right.

* Adjustment and measurement should be made at the points one

inch inside the fluorescent screen.

7. For the up/down swing, swing the DY and insert a wedge so

that the up and down pins are equal at the top and bottom.

Adjust the DY TLV VR so that the horizontal trapezoid is

equal at the left and right. Insert the wedge firmly so that the

DY does not shake.

8. Check the landing of each corner, and if it does not satisfy the

specification, adjust the landing of four corners using "LCC

LT", "LCC LB", "LCC RT" and "LCC RB".

However, the register adjustment must be limited within the

following range.

"LCC NS"

"LCC LT", "LCC LB", "LCC RT", "LCC RB" 128 ± 40

After adjustment, save the service data.

9. Remove the sensor and wobbling coil.

10. Switch the signal to R.G.B., and check that each color is pure.

11. Check that the DY is not tilting.

128 ± 15

128 ± 40

(µm)

0 ± 3

0 ± 7.5 0 ± 3

0 ± 5

0 ± 3

0 ± 7.5 0 ± 3

(µm)

± 6

± 4

± 6

(µm)

128 ± 15