- ページ 38

ストレージ Dell PowerVault LTO4-120のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Dell PowerVault LTO4-120 44 ページ。 Powervault tape systems
Dell PowerVault LTO4-120 にも：スタートマニュアル (33 ページ), ハンドブック (28 ページ), ユーザーマニュアル (26 ページ)

ページを印刷する

09h

Write protect

0Ah

No removal

0Bh

Cleaning media

Unsupported

0Ch

format

Cartridge memory

0Fh

chip failure

10h

Forced eject

Tape directory

12h

corrupted in the

cartridge memory

14h

Clean now

15h

Clean periodic

16h

Expired clean

Invalid cleaning

17h

tape

1Eh

Hardware A

1Fh

Hardware B

20h

Interface

21h

Eject media

22h

Download fail

24h

Drive temperature

25h

Drive voltage

Diagnostics

27h

required

Tape directory

33h

invalid at unload

Tape system area

34h

write failure

Tape system area

35h

read failure

Recovering a Tape Cartridge

If problem-determination procedures identify the tape drive as the source of the problem and you are unable to eject the tape cartridge using the eject

button, perform the following steps to reset the drive to recover the cartridge:

1. Press and hold the eject button for 10 seconds, then release.

The status light turns amber and the drive starts through its hardware test process.

When the hardware test completes, the status light turns green.

If a cartridge is in the drive, the status light flashes green until the cartridge is rewound.

Set when the tape drive detects that the

tape cartridge is write-protected.

Set when the tape drive receives an

UNLOAD command after the system

prevented the tape cartridge from being

removed.

Set when you load a cleaning cartridge

into the drive.

Set when you load an unsupported

cartridge type into the drive or when the

cartridge format has been corrupted.

Set when a cartridge memory (CM) failure

is detected on the loaded tape cartridge.

Set when you manually unload the tape

cartridge while the drive was reading or

writing.

Set when the drive detects that the tape

directory in the cartridge memory has

been corrupted.

Set when the tape drive detects that it

needs cleaning.

Set when the drive detects that it needs

routine cleaning.

Set when the tape drive detects a

cleaning cartridge that has expired.

Set when the drive expects a cleaning

cartridge and the loaded cartridge is not a

cleaning cartridge.

Set when a hardware failure occurs that

requires that you reset the tape drive to

recover.

Set when the tape drive fails its internal

self tests.

Set when the tape drive detects a

problem with the SCSI or LDI (RS-422)

interface.

Set when a failure occurs that requires

you to unload the cartridge from the drive.

Set when a field microcode replacement

(FMR) image is unsuccessfully downloaded

to the tape drive via the SAS interface.

Set when the drive's temperature sensor

indicates that the drive's temperature is

exceeding the recommended temperature

of the system (see "Specifications").

Set when the drive detects that the

externally supplied voltages are either

approaching the specified voltage limits or

are outside the voltage limits (see

"Specifications").

Set when the drive detects a failure that

requires diagnostics to isolate the

problem.

Set when the tape directory on the tape

cartridge that was previously unloaded is

corrupted. The file-search performance is

degraded.

Set when the tape cartridge that was

previously unloaded could not write its

system area successfully.

Set when the tape system area could not

be read successfully at load time.

Make sure that the cartridge's write-protect switch is set so that

the tape drive can write data to the tape (see the

Write-Protect

Switch" section).

Refer to the documentation for your system's operating system.

No action required.

Use a supported tape cartridge.

Replace the cartridge. If this error occurs on multiple tapes, see

error code 6 in

"Descriptions and Corrective

No action required.

Reread all data from the tape to rebuild the tape directory.

Clean the tape drive. See the

"Cleaning the Tape

section.

Clean the tape drive as soon as possible. The drive can continue

to operate, but you should clean the drive soon. See the

"Cleaning the Tape

Mechanism" section.

Replace the cleaning cartridge.

Use a valid cleaning cartridge.

If resetting the drive does not recover the error, use the error

code from the single-character display, library user interface, or

SCSI drive sense data. See

"Descriptions and Corrective

Actions."

Use the error code on the single-character display, library user

interface, or SCSI drive sense data. See

Corrective

Actions."

Locate error code 8 or 9 in

"Descriptions and Corrective

Actions."

Unload and reload the tape cartridge.

Ensure that it is the correct image. Download the FMR image

again.

See error code 1 in

"Descriptions and Corrective

See error code 2 in

"Descriptions and Corrective

See error code 6 in

"Descriptions and Corrective

Rebuild the tape directory by reading all the data.

Copy the data to another tape cartridge, then discard the old

cartridge.

Copy the data to another tape cartridge, then discard the old

cartridge.

"Setting the

Actions."

Mechanism"

"Descriptions and

Actions."