DVR AVYCON AVR-T904A-1TのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。AVYCON AVR-T904A-1T 2 ページ。 Hybrid dvr
ページを印刷するHybrid DVR
Quick Start Guide
Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes.
All the examples and pictures used here are for reference only. There may be several technically incorrect places
or printing errors in this manual. The updates will be added into the new version of this manual. The contents of
this manual are subject to change without notice.This device should be operated only from the type of power
source indicatedon the marking label. The voltage of the power must be verified before using the same.
1. HDD Installation
This series of the product supports 1 SATA hard drive. Please make sure
that the device is powered off before the installation. The pictures of
the installation are only for reference, please take the real object as the
standard.
2. Screw the screws into the HDD
1. Loosen the screws to open the
but not tighten them.
cover.
4. Connect the power and data
3. Place the HDD onto the bottom
cables.
of the machine.
6. Install back the cover and secure
5. Turn over the machine and secure
it with the screws.
the HDD with the screws.
2. Rear Panel Installation
4
3
2
1
4
3
2
1
ALARM IN
CVBS
VIDEO IN
AUDIO
4
3
2
1
AUDIO IN
OUT
ALARM OUT
VGA
Rear Panel for 4CH
A L A R M O U T A L A R M I N
4
2
8
6
4
2
4
3
2
1
3
1
7
5
3
1
C V B S
A U D IO O U T
A U D IO I N
V ID E O I N
Rear Panel for 8CH
AUDIO
OUT
14
6
16
12
10
8
4
2
AUDIO
15
13
11
9
7
5
3
1
VIDEO IN
IN
Rear Panel for 16CH
The interfaces of the rear panels are for reference only.
3. Startup & Shutdown
• Startup
1. Connect the monitor and the power.
2. The device will boot and the power indicator will display blue.
3. A wizard window will pop up.
• Shutdown
Go to "Main Menu" and then select "Shutdown" icon. This will bring up
a shutdown window. The device will shut down by clicking "OK" button.
Then disconnect the power.
4. Login
For our T900 series DVRs, the default username is admin and the
default password is 123456. When starting T900 series DVR for the
first time, you will see a prompt to begin a startup wizard. You can
skip this wizard if you would like, but it will help you configure basic
settings for your DVR. The wizard may allow you to also change the
default password for better security. If you decide to skip the wizard,
to access the live view and start using your DVR click on the Start
button in the bottom left of the menu bar on the bottom of the
screen and then click on Login and enter in the default password.
Login
Username
adm in
Enter Password
Password
Display Password
Log In Automatically
Edit Security Question
Login
5. Analog Camera Connection
First connect the camera to the DVR. Then go to Start → Settings
→ Camera → Manage Camera → Signal Access Set to checkmark
the video mode. The actual signals input shall correspond to the
B
A
video mode. Please refer to User Manual for details.
LAN
USB DC12V RS485
6.
Network Configuration & Add IP Camera
After you finish adding IP cameras, you can see the live images
through the monitor of the DVR. The following will mainly
introduce how to add the IP cameras via LAN/WAN.
• LAN
1. Set the network of the DVR. Go to Start → Settings → Network
→ TCP/IPv4. Input IP address, subnet mask, gateway, etc. If using
R S 485
DHCP, please enable DHCP in both the DVR and the router.
2. Go to Start → Settings → Network → Port. Input HTTP port
V G A
L A N
U S B
D C 12V
B
A
(the default value is 80), server port (the default port is 6036).
3. Click "Apply" to save the settings.
In te r n e t
TCP/IPv4
IP Address Settings
RS485
Ethernet Port 1 ( Online )
VGA
LAN
USB DC12V
B
A
Obtain an IP address automatically
IP Address
Subnet Mask
Gateway
Obatin DNS server address automatically
Preferred DNS
Alternate DNS
Quickly Add
Manually Add
No.
IP Address
1
192.168.2.45
Selected: 1/1
Remain Bandwidth: 10 / 10 Mb
Cancel
Port
DDNS
E-mail
UPnP
NAT
Network Status
192 . 168 .
1 .
2
0
.
0
.
0 .
0
192 . 168 .
1 .
1
192 . 168 .
1 .
1
0
.
0
.
0 .
0
Add Camera
Port
Edit
Subnet Mask
Protocol
Model
Version
80
255.255.255.0
XXX
XXX
4.0.0.1.beta1
Default Password
Add
Cancel
Edit IP
Mac Address
CE :98 :23 :75 :35 :22
IP Address
192 .168 . 1 . 45
Subnet Mask
255 . 255 . 255 . 0
Gateway
192 .168 . 1 . 1
Usernam e
admin
Password
OK
Cancel