- ページ 5
サブウーファー EarthQuake MiniMe P12のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。EarthQuake MiniMe P12 16 ページ。 Earthquake sound subwoofers user's manual
ページを印刷する
(1)
Line Level RCA
Inputs and Outputs
(2) Speaker
Level
Inputs and Outputs
(1) Line Level RCA Inputs
Connect with RCA type patch cords to the line level
output of your receiver or pre-amp. If your pre-
amplifier or receiver has a single sub/LFE output,
connect it to the subwoofer's left input jack. There is
no need to use the subwoofers right input jack. If you
want to run your main/satellite speakers full range,
use a "Y" adapter at the pre-amplifier outputs. In this
way, you can send the pre-amplifier's output signal to
your main amplifier and to the subwoofer at the same
time.
(2) High Level Inputs / Outputs
Under normal conditions, the preferred connection is
through the Line Level inputs. If this is difficult or not
possible in your system, then you can use the
Speaker Level inputs. Also, if you experience
excessive noise or hum with the Line Level input,
often a simple change to the Speaker Level input will
result in a lower background noise level.
Connect the Speaker Level inputs to the speaker-level
outputs of your amplifier or receiver using speaker
wire. The binding posts can accept bare wire
connections only.
High Level: Connecting the Subwoofer using the high
level speaker connections: On the rear of your MiniMe
Subwoofer are two pairs of red and black binding
posts. One set is marked "Input" and one set is
marked "Output", with each pair designated as left or
right. Each post is color-coded black/red. These
Earthquake • MiniMe User Manual
Control Panel Overview
600 WATTS
POWERED
SUBWOOFER
DIGITAL
P O W E R
WARNING
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
110-120V
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
220-240V
Earthquake Sound, 2727 McCone Avenue, Hayward, CA 94545 USA
(3) Voltage Selection Switch
LEFT
RIGHT
VOLUME
POWER
MIN
MAX
FREQUENCY
50Hz
160Hz
MODE
SUB
LFE
PHASE
0
180
AUTO
OFF
ON
110-120VAC~60Hz
220-240VAX~50Hz
ON
FUSE
OFF
FUSE: 115V, T6.4AL/250V
FUSE: 230V, T3.2AL/250V
www.earthquakesound.com
(4) Manual ON/OFF Switch
terminals will accept up to 16-gauge quality speaker
wire. The Inputs should be connected to the left and
right speaker terminals of your amplifier or receiver.
The Outputs should run from the subwoofer to the left
and right satellite speakers. Remember: Always
connect red-to-red and black-to-black, when making
connections between an amplifier/receiver to the
subwoofer. If you inadvertently reverse one of the
connections (i.e., red-to-black), you will notice a lack
of bass from your subwoofer.
(3) Voltage Selection Switch
The voltage switch is positioned according to area
voltage requirements. It has been pre-set
prior to shipping from the factory.
CAUTION
Do not try to alter the voltage setting, as doing so will
result in a blown fuse. A wrong setting
may result in damaged electronics.
(4) Manual ON/OFF Switch
In the "ON" position, the subwoofer will remain "on"
constantly or can turn "on" and "off" automatically
when the "AUTO/ON" circuit is engaged. In the "OFF"
position, the subwoofer will remain off until the switch
is manually turned back to the "ON" position.
(5) Line Fuse
The subwoofer is supplied with a conservative, slow-
blow type fuse to protect the electronics.
Overview Continued On Next Page»
5
(12) Volume Control
(11) 50Hz - 160Hz
Frequency Adjustment
(10) Sub Operation Switch
(9) 0-180° Phase Shift
(8) Power Status LED
(7) Auto ON/OFF
(6) 110-120V AC Power Connection
(5) Line Fuse