- ページ 2

防犯カメラ Allied Vision AVT PikeのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Allied Vision AVT Pike 2 ページ。

ページを印刷する

Hardware Installation

To install hardware read Hardware Installation Guide.

Note

You will find this document in the following directory:

<CD ROM>:\products\cameras-general

•

All_HardInst_Vx.y.z_en.pdf

Software Installation

To install software read (depending on your system):

•

FirePackage User Guide

•

FirePackage64 User Guide

•

Fire4Linux User Guide

Note

You will find these documents in the following directory:

<CD ROM>:\products\AVT_FirePackage_x_y_z

•

FirePackage_UserGuide_Vx.y.z_en.pdf

•

FirePackage_x64_UserGuide_Vx.y.z_en.pdf

<CD ROM>:\products\linux

Caution

Hot-plug precautions

•

The physical ports may be damaged by excessive ESD

(electrostatic discharge), when connected under powered

conditions. It is good practice to ensure proper grounding

of computer case and camera case to the same ground

potential, before plugging the camera cable into the port

of the computer. This ensures that no excessive difference

of electrical potential exists between computer and cam-

era.

•

It is very important not to exceed an inrush current of

18 mJoule in 3 ms. (This means that a device, when pow-

ered via 12 V bus power must never draw more than 1.5 A,

even not in the first 3 ms.)

•

Higher inrush current may damage the physical inter-

face chip of the camera and/or the phy chip in your PC.

•

Whereas inrush current is not a problem for one Pike/Stin-

gray camera, daisy chaining multiple cameras or supplying

bus power via (optional) HIROSE power out to circuitry

with unknown inrush currents needs careful design consid-

erations to be on the safe side.

Screw-lock and other precautions

•

Also, all AVT 1394b camera and cables have industrial

screw-lock fasteners, to insure a tight electrical connec-

tion that is resistant to vibration and gravity.

•

We strongly recommend using only 1394b adapter

cards with screw-locks.

•

Make sure not to touch the shield of the camera cable

connected to a computer and the ground terminal of the

lines at the same time.

•

If you are charged: before touching the shield of the cam-

era cable, make sure to discharge first (by touching the

ground terminal of the lines).

•

Use only DC power supplies with insulated cases. These are

identified by having only two power connectors.

•

If you feel uncomfortable with the previous advice or if

you have no knowledge about the connectivity of an

installation, we strongly recommend powering down all

systems before connecting or disconnecting a camera.

PIKE Instruction Leaflet V2.0.0

Safety instructions

Note

•

There are no switches or parts inside the camera that

require adjustment. The guarantee becomes void upon

opening the camera casing.

•

If the product is disassembled, reworked or repaired by

other than a recommended service person, AVT or its

suppliers will take no responsibility for the subsequent

performance or quality of the camera.

•

The camera does NOT generate dangerous voltages

internally. However, because the IEEE 1394a standard

permits cable power distribution at voltages higher

than 24 V, various international safety standards apply.

Note

•

All color models are equipped with an optical filter to

eliminate the influence of infrared light hitting the

sensor. Please be advised that, as a side effect, this fil-

ter reduces sensitivity in the visible spectrum. The opti-

cal filter is part of the back focus ring, which is

threaded into the C-Mount.

•

B/w models come with a sensor protection glass

mounted in the back focus ring.

Cautions

Caution

Hot-plug precautions

•

Although FireWire devices can theoretically be hot-

plugged without powering down equipment, we

strongly recommend turning the computer power off,

before connecting a digital camera to it via a FireWire

cable.

•

Static electricity or slight plug misalignment during

insertion may short-circuit and damage components.

Caution

•

Mount/dismount lenses and filters in a dust-free envi-

ronment, and do not use compressed air (which can push

dust into cameras and lenses).

•

Use only optical quality tissue/cloth if you must clean a

lens or filter.

•

Read Hardware Installation Guide, Chapter Cleaning

instructions.

Environmental conditions

•

Housing temperature (when camera in use):

•

Ambient temperature during storage:

•

Relative humidity:

20 % ... 80 % without condensation

•

Protection:

IP 30

All texts, pictures and graphics are protected by copyright and other laws pro-

tecting intellectual property. It is not permitted to copy or modify them for trade

use or transfer, nor may they be used on web sites.

Allied Vision Technologies GmbH 08/2008

Managing Director: Mr. Frank Grube

Tax ID: DE 184383113

PIKE Instruction Leaflet V2.0.0

+ 5 °C ... + 50 °C

- 10 °C ... + 60 °C

PIKE Instruction Leaflet V2.0.0