- ページ 5

スプレッダー EarthWay EV-N-SPRED C24HDSのPDF 組立・取扱説明書をオンラインで閲覧またはダウンロードできます。EarthWay EV-N-SPRED C24HDS 10 ページ。 Broadcast spreader
EarthWay EV-N-SPRED C24HDS にも：組立・取扱説明書 (9 ページ)

ページを印刷する

17. For normal operation both doors should be fully opened. To reduce flow to the left side, partially or completely close the

door over the rear (LARGE) hole. To reduce flow to the right side, partially or completely close the door over the front (SMALL)

hole. Close both doors for a narrow center spread pattern.

WARNING: If the optional side deflector is being used in the down position, the plate over the rear (LARGE) hole MUST BE

CLOSED or an over application of material will occur.

SPREAD PATH

FULL Rate

The settings furnished on the Setting Matrix are intended as a guide only. Variations in physical characteristics of material

applied, walking speed, and roughness of ground surface may require slightly different spreader settings. Due to these

conditions, Earthway Products, Inc. makes no warranty as to the uniformity of coverage actually obtained from the settings listed.

Earthway Products, Inc. warrants this product free of defects in original workmanship and materials for a period of 5-Years

to the end user with the original purchase receipt. If a manufacturing non-conformance is found, Earthway Products, Inc.

at its discretion will repair or replace the part(s) or product at no charge provided the failure is not the result of incorrect

installation, mishandling, misuse, tampering, or normal wear and tear as determined by Earthway. Earthway at its discretion

may require that the part(s) or product be returned along with the original purchase receipt at owners' expense for examination

and compliance with the terms of this warranty. Do not return any product without first receiving authorization from Earthway

Products, Inc. To seek remedy under this warranty, contact Earthway Products, Inc. at 574-848-7491, techsupport@earthway.

com or write to Earthway Products, Inc. P.O. Box 547 Bristol, Indiana 46507 and describe the nature of the manufacturing

defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor charges associated with repair

or replacement of non-conformances are specifically excluded. Due to the corrosive nature of most fertilizers and ice melt

products, Earthway Products, Inc. makes no warranty against and specifically excludes part(s) or product degradation or failure

due to corrosion or its effects. Clean and dry your spreader thoroughly after each use, as a preventative measure, coat all

metal parts with a light oil or silicon spray.

Before filling hopper, become familiar with the operation of this spreader.

5 Obtain proper setting for material to be used from the enclosed SETTING MATRIX included with this spreader, or from our

web site under the MANUALS SECTION.

5 Move stop bolt on rate gauge assembly to the proper setting.

5 While pushing spreader forward, pull control lever back to stop bolt.

5 To stop, push lever forward to close flow holes before you stop moving.

5 When finished, empty any remaining material from hopper.

5 Thoroughly wash spreader and allow to dry before storing. Apply coating of light oil to help prevent corrosion.

5 If you use Rock Salt, remove agitator when using Rock Salt to prevent damage to the gearbox.

Earthway Products, Inc.

1009 Maple Street, PO Box 547

Bristol, IN 46507

For Your Records

Date Purchased

Place of Purch

HALF Rate

(one pass)

5-YEAR LIMITED WARRANTY

OPERATING INSTRUCTIONS

ase

(two passes)

Each adjustable port

All spare parts listed may be ordered direct from

Be sure to give the following information when ordering.

Call (574) 848-7491, 800-294-0671, or email: parts@earthway.

Both ports open

Both ports closed

has 8 positions

One port closed

HOW TO ORDER SPARE PARTS

EarthWay Products, Inc.

Model Number

Part Number

Part Description

com for current prices.

PAGE 5