- ページ 5

録音機器 ALLNIC AUDIO h-1201のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。ALLNIC AUDIO h-1201 11 ページ。 Phono stage

ページを印刷する

for such applications to clean the contacts from time to

time, as you deem appropriate.

INITIAL SET-UP

LOCATION, LOCATION, LOCATION

Like all audio products using tubes, the Allnic Audio H-1201

needs to be placed on a solid stand in a location that provides

good air circulation around the phono stage.



DO NOT cover the top of the H-1201 phono stage or

tube chimneys.



DO NOT place the unit on carpet or foam.



DO NOT subject the unit to knocks and shocks as you

move it around. This advice is meant particularly for

those who may want to place the H-1201 on some

kind of after-market isolation feet or similar devices.

Dropping the H-1201 is not a good thing to do and

may void the warranty.



DO NOT place the unit near a strong light or heat.



DO NOT place anything heavy on the unit.



DO NOT allow rubber or vinyl materials to rest on the

unit's chassis for long periods of time. This could

discolour the metal.



DO place the unit on a shelf or stand that is stable

and not subject to vibration or sudden shock.



DO consider using a high quality power cord and

inter-connects, for both inputs and outputs. The H-

1201 is a highly sensitive piece of electronic designed

for neutrality and will output what you put into it.



DO try to place the H-1201 away from major sources

of RFI and EMI; though well shielded, the H-1201 will

function best away from large power transformers

and other sources of such interference.

POWER CONNECTIONS

The H-1201 uses a standard three prong male IEC

connection for AC input. You need to use a power cord with

a female three prong IEC connector at one end (See Figure

1).

The H-1201 power supply you have purchased is set

internally for AC 110/120 volt – 60 HZ operation. There is no

way to change this to another AC setting without return of

the unit to the factory for re-wiring, at the owner's cost,

including transport both directions.

INPUTS

There are two (2) pairs of single-ended (RCA) inputs, one for

Moving Coil (MC) cartridges and the other for Moving Magnet

(MM) cartridges. These two pairs are located in the middle of

the rear of the H-1201 (See Figure 1) and labeled "MC – input –

MM" between the top and bottom connectors. Facing the rear

of the H-1201, the left hand pair of inputs is the moving coil

cartridge input; the right is for moving magnet cartridges. Each

pair of inputs is aligned vertically, with the left channel "left"

labeled input at the top and the "right" labeled input on the

bottom.

To the left and right (facing the rear panel) of the MC and

MM input connections respectively is a screw type ground

connector. Either or both of these may be used for multiple

ground connections.

When you are facing the front of the H-1201, the input

connections are in the centre of the unit, with the MC

connections on the right and the MM connections immediately

to their left.

The H-1201 has been designed and manufactured to work most

synergistically with Allnic Audio preamplifiers, pre-phono stages

and equalization products.

OUTPUTS

The H-1201 is equipped with one set of unbalanced or "single-

ended" (RCA) outputs The output connection is just to the left

(facing the rear panel) of the AC IEC power cord connection. The

left channel output connection is the top one and is labeled

"left"; the bottom, "right" (See Figure 1).

Moving Coil (MC) Transformer Controls

On the top of each channel's MC transformer on the centre

rear of the chassis deck of the H-1201 (See Figure 4), there is

a rotating control (See Figure 3). Turn the control knob to

select from four gain factors: +22dB, +26dB, +28dB and

+32dB. Combined with the H1201's 40dB native gain, for MC

there is 62dB, 66dB, 68dB and 72dB of gain available. Each of

the second set of indicators on the top of the transformers

only marks the impedance tied to the gain setting diagonal