- ページ 4

フラッドライト Dialight ProSiteのPDF 取付・取扱説明書をオンラインで閲覧またはダウンロードできます。Dialight ProSite 20 ページ。 For cid2/ciid1/ciid2/ciii
Dialight ProSite にも：取付・取扱説明書 (18 ページ), 取付・取扱説明書 (9 ページ), 取付・取扱説明書 (8 ページ)

ページを印刷する

Opening/Closing the Luminaire

This luminaire has 2 lids, a driver enclosure lid

and front access lid. Both lids are retained by

captive bolts and offer a combination head

style for ease of entry. The front access lid is

used for wiring the luminaire for bracket

models while slip fitter models do not use the

front access lid.

Loosen the 4x screws and remove the lid to

gain access to the terminal blocks for wiring.

When wiring is complete, reattach the lid,

and tighten screws back down.

Torque: 3,4 N-m [30 in-lbs]

4x Captive Bolts

NOTE: The lid is secured to the wiring box via

a lanyard; eliminating risk of dropping the lid

upon removal.

NOTE: The lid of the luminaire should be

oriented as shown above. The Dialight logo

should be aligned with the mounting bracket.

Electrical Connections

The terminal block is suitable for multi-

stranded or single core wires. The parameters

can be found in Technical Data.

Push Down Terminal Models: F*B********V**

Push down at the 'cross point', insert wire, and

release.

Conductor Range

0,5-4 mm² [20-12 AWG]

Screw Down Terminal Models: F*B********U**

For input power terminal block, loosen

terminal screw, insert wire, and tighten screw.

Conductor Range

0,5-6 mm² [20-10 AWG]

10 mm [0,39 in.]

9100FLM000903 REV B

Page 4 of 20

ProSite Floodlight for ATEX/IECEx Zone 2

For dimming & Dali lines, push down at the

'cross point', insert wire, and release.

Conductor Range

0,5-4 mm² [20-12 AWG]

Single Phase Connections

The connections are marked on the terminal

block or on a label and are presented in the

table below.

SYMBOL

DIM +

DIM -

DALI

0-10 VDC Dimming (If Applicable)

Dimming is controlled by means of a 0-10

VDC signal (to be provided by the installer) to

control the level of dimming. At 10 volts, the

output of the unit is 100%; at 0 volts, the output

will shut off. The DC dimming voltage should

not exceed 15 VDC. Increasing the voltage

from 10 VDC to 15 VDC will not result in

additional light output.

WARNING: Never connect the dimming wires

to the Hot or Neutral supply wires.

An analog 0-10 V active dimmer may be

connected to the two wires to control the

light output of the fixture. Multiple lights may

be connected to the same dimmer, as long

as the maximum current rating of the dimmer

is not exceeded.

See table for current sinking capabilities of

the

dimmer.

approximately linearly with control voltage,

with 10 V corresponding to 100% light output.

Strip Length

9 mm [0,35 in.]

F1B***********

F2B****(F/H)******

F2B****(L/N)******

Strip Length

9 mm [0,35 in.]

COLOR

CONNECTION

120-277VAC

GREEN/

EARTH/

YELLOW

GROUND

WHITE

NEUTRAL

BLACK

LIVE

130-250VDC

GREEN/

EARTH/

YELLOW

GROUND

WHITE

BLACK

CONTROLS

VIOLET

DIMMING +

GREY

DIMMING -

ORANGE

DALI

OR YELLOW

Variable Voltage Control

Light

output

will

Part Number

Current

0,5 mA

1,0 mA

Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727

Tel: +1 732 919 3119 Fax: +1 732 751 5778

NOTE: Simply shorting the two wires together

will cause the light to shut off.

WARNING: Improper installation, operation,

or maintenance of this luminaire may result in

the invalidation of the warranty, certificate,

or declaration of conformity.

DALI Control (If Applicable)

DALI is used to control/schedule and group

the luminaire. A DALI controller is to be

provided by the installer. The luminaire will not

provide a bus signal. A Bus power supply

should be used to provide a Bus signal

according to the DALI standard.

WARNING: Never connect the DALI wires to

the Hot/Live or Neutral supply wires.

WARNING: Do not connect the DALI wires to

the dimming wires.

For luminaires containing one power supply

[F1B********** & F2B****(F/H)******], only one

DALI address will be assigned by the DALI

controller.

For luminaires containing two power supplies

[F2B****(L/N)******], two DALI addresses will

be assigned by the DALI controller.

NOTE: The DALI circuit in two power supply

luminaires are already internally wired as a

daisy chain to allow for commissioning and

discovery. The

connected to the DALI terminal block

positions in the wiring compartment.

vary

NOTE: Make sure luminaires containing two

power supplies are grouped and scheduled

together for the luminaire to function in the

correct manner.

WARNING: Improper installation, operation,

or maintenance of this luminaire may result in

the invalidation of the warranty, certificate,

or declaration of conformity.

Bus wire

needs to be