- ページ 2

ネットワークカード Dialogic Media Board D/120JCT-LS-EWのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Dialogic Media Board D/120JCT-LS-EW 2 ページ。 Dialogic media board installation guide

ページを印刷する

4. Insert the board's edge connector into the bus

slot, and apply firm pressure to the top edge of

the board until the board is fully seated in the

edge connector.

Remove

Cover

PCI Express

Plate

Board

Computer

Chassis

PCI Express

Slots

PCI Slots

5. Reinstall the retaining screw.

6. Repeat steps 1 through 5 for any additional

boards you are installing.

7. Connect the telephony boards together with a

CT Bus cable of the appropriate size (not

included). If possible, use a cable assembly that

matches the number of boards in your system.

If the cable has more than one unused

connector, install the cable so that all the

unused connectors are at one end of the cable.

CT Bus

Colored

Cable

Stripe

(Pin 1)

Note:

Your CT Bus cable may

have a different number of

connectors (drops).

8. Replace the computer's cover.

9. Reconnect the computer's power cord.

6. Connecting to External

Equipment

Each of the six RJ-14 jacks on the rear bracket of

the Dialogic

D/120JCT-LS-EW board supports two

analog telephony channels. A standard telephone

will not function when directly connected to the

board.

The following figure illustrates the pinout of the RJ-

14 jacks, which provide two tip/ring pairs with an

earth recall, one set for each telephony channel.

Pinout for RJ–14 Jacks on D/120JCT-LSEW Bracket

Line 2 Earth Recall

Line 2 Ring

Line 1 Tip

Line 1 Ring

Line 2 Tip

Line 1 Earth Recall

7. After Installing the Board

If you are installing the Dialogic

D/120JCT-LS-EW

in a system that already has the Dialogic

system

release software installed, you may not need to

install a new or upgraded software release to

support the board. The Dialogic

D/120JCT-LS-EW

has been designed to be compatible with existing

System Release 6.x software versions that support

PCI boards. Please refer to the Release Update

document for your release version for up-to-date

information about support for PCI Express boards

and any known issues relating to their use.

If this is the first Dialogic

telecom board you have

installed in your system, you will need to install an

appropriate version of the Dialogic

system release

software and configure the software for the specific

board(s) you are using. Refer to the installation

and configuration documentation that accompanies

the release for instructions.

When configuring the system for the Dialogic

D/120JCT-LS-EW board, use the same menu

selections and configuration settings that are

documented for the PCI version of the Dialogic

D/120JCT-LS.

8. Removing the Board

Removal of the Dialogic

D/120JCT-LS-EW board is

essentially the reverse of the installation

procedure:

1. Observe anti-static precautions.

2. Disconnect the telephony cables.

3. Remove the computer's power cord.

4. Remove the computer's cover.

5. Disconnect the CT Bus cable (if applicable).

6. Remove and set aside the board's retaining

screw.

7. Remove the board and place it static-protective

packaging.

9. Contacting Technical Support

Dialogic provides technical support for its products

through a network of value added distributors who

are trained to answer technical questions on

installing and configuring Dialogic

products. If

you are unsure how to contact your support

channel, please call Dialogic in the United States at

973-967-6600 (9am - 5pm EST) and we will assist

in obtaining the appropriate support channel.

Outside the United States please refer to

http://www.dialogic.com/support/contact to obtain

local contact information.

Dialogic also provides direct support via Dialogic®

Pro™ Services agreements. For more details of

direct support from Dialogic please refer to

http://www.dialogic.com/support/DialogicPro.

10.Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following:

http://www.dialogic.com/support/hwfaults

11.Warranty Information

For specific warranty information for this board,

refer to the Warranty section of the Products page,

located at this URL:

http://www.dialogic.com/warranties/.

12.Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales

Office for your area. Address, telephone and fax

numbers, are available at the Dialogic website

located at: http://www.dialogic.com/contact.htm.

To purchase Dialogic® products, please refer to the

following website to locate the appropriate

supplier: http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for

informational use only and are subject to change without

notice and do not represent a commitment on the part of

Dialogic Corporation or its subsidiaries ("Dialogic").

Reasonable effort is made to ensure the accuracy of the

information contained in the document. However, Dialogic

does not warrant the accuracy of this information and

cannot accept responsibility for errors, inaccuracies or

omissions that may be contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN

CONNECTION WITH DIALOGIC® PRODUCTS. NO LICENSE,

EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO

ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY

THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED

AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC

ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC

DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY,

RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS

INCLUDING LIABILITY OR WARRANTIES RELATING TO

FITNESS FOR A PARTICULAR PURPOSE,

MERCHANTABILITY, OR INFRINGEMENT OF ANY

INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life

saving, life sustaining, critical control or safety systems, or

in nuclear facility applications.

It is possible that the use or implementation of any one of

the concepts, applications, or ideas described in this

document, in marketing collateral produced by or on web

pages maintained by Dialogic may infringe one or more

patents or other intellectual property rights owned by third

parties. Dialogic does not provide any intellectual property

licenses with the sale of Dialogic products other than a

license to use such product in accordance with intellectual

property owned or validly licensed by Dialogic and no such

licenses are provided except pursuant to a signed

agreement with Dialogic. More detailed information about

such intellectual property is available from Dialogic's legal

department at 9800 Cavendish Blvd., 5th Floor, Montreal,

Quebec, Canada H4M 2V9. Dialogic encourages all

users of its products to procure all necessary

intellectual property licenses required to implement

any concepts or applications and does not condone

or encourage any intellectual property infringement

and disclaims any responsibility related thereto.

These intellectual property licenses may differ from

country to country and it is the responsibility of

those who develop the concepts or applications to

be aware of and comply with different national

license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic

Pro and SIPcontrol, among others, are either registered

trademarks or trademarks of Dialogic. Dialogic's

trademarks may be used publicly only with permission

from Dialogic. Such permission may only be granted by

Dialogic's legal department at 9800 Cavendish Blvd., 5th

Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized

use of Dialogic's trademarks will be subject to full respect

of the trademark guidelines published by Dialogic from

time to time and any use of Dialogic's trademarks requires

proper acknowledgement. The names of actual companies

and products mentioned herein are the trademarks of their

respective owners.