コンピュータ・ハードウェア Dialogic D4PCIUのPDF クイックインストールをオンラインで閲覧またはダウンロードできます。Dialogic D4PCIU 2 ページ。 Quick install card for pci universal
Dialogic D4PCIU にも：クイックインストール (2 ページ)

ページを印刷する

Dialogic

D/4PCIU,D/4PCIUF

Quick Install Card for PCI Universal

Part Number 64-0048-02

Before You Begin

Protecting the Board from Damage

CAUTION

All computer boards are sensitive to

electrostatic discharge ("ESD"). Handle all static-sensitive

boards and components at a static-safe work area, and observe

anti-static precautions at all times.

If you are not familiar with ESD safety precautions, visit

http://www.dialogic.com/support/hwinstall

Unpacking the Board

Unpack the Dialogic

D/4PCIU, D/4PCIUF board ("board")

according to the following steps:

Prepare a static-safeguarded work area.

Carefully remove the board from the shipping

carton and anti-static packaging. Handle the board

by the edges and avoid touching the board's

components.

Lay the board on the static-dissipative work

surface.

Note: Place boards in static-shielding bags when carrying

boards from station to station.

CAUTION: Do not remove the board from the anti-static

packaging until you are ready to install it. Observe proper

anti-static precautions at all times.

Configuring the Hardware

Initial Hook State

The position of slide switch SW4 determines how the board

responds to an incoming call when the chassis power is on but

the board is not initialized. Refer to the Physical Description

section. Set the SW4 slide switch as follows:

SW4 = On-hook (default): Callers hear ringing.

SW4 = Off-hook: Callers hear a busy signal.

Dialogic Corporation.

to learn more.

NOTE: If the chassis power is off, callers hear ringing

(on-hook).

The Dialogic

technology, including hardware auto-configuration for IRQ

and memory address. This technology enables quick

installation and operation using the factory default hardware

settings.

The system software assigns board instance numbers in

ascending order (beginning with 0) as it detects each board in

your system. A board instance number is the identification

(ID) number used by the system software to recognize the

board. Each Board ID is based on the SW30 rotary switch

setting. See the Physical Description section.

NOTE: The ascending Board IDs automatically assigned by

the system may not correspond to a physical order in the

chassis.

Board Identification

D/4PCIU board uses Plug and Play

Geographical Sequence

Leave SW30 set to Board ID 0 (default) to let the system

automatically assign board instance numbers by PCI bus

logical slot number. This method is not available for ISA bus

boards.

NOTE: If you add or remove a board, the system may

change the existing board instance (ID) numbers.

Programmable Sequence

You must set SW30 to a unique number for each installed

board. Use a non-metallic screwdriver to turn SW30 to 1 of

16 board settings, 0–9 or A–F. You should assign sequential

numbers to each Dialogic

board, starting at 1. This method is

also used for all ISA bus boards.

Precedence in Mixed Systems

In systems where both ISA and PCI boards exist, PCI boards

take precedence and are numbered before ISA boards. Also,

when using both geographical and programmable assignment

methods, PCI boards that use SW30 setting 0 are numbered

before PCI boards that use SW30 settings 1–9 or A–F.

NOTES: After the hardware and the system software are

installed in a Windows system, refer to the Dialogic

Configuration Manager (DCM) utility to retrieve the assigned

board instance (ID) number(s). After the hardware and the

system software are installed in a Linux system, refer to the

proper configuration files to retrieve the assigned board

instance (ID) number(s).