- ページ 18
溶接アクセサリー Miller PORTA-MIGのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Miller PORTA-MIG 43 ページ。
ページを印刷する
11.
CGA
Pamphlet
P-i,
SAFE HANDLING OF COM
PRESSED GASES
IN
CYLINDERS
obtainable
from the
Compressed
Gas
Association,
500
Fifth
Avenue,
New
York,
NY
10036.
12.
CSA
Standard
Wi
17.2,
CODE FOR SAFETY
IN
WELDING
AND
CUTTING obtainable
from the
Canadian
Standards
Association,
Standards
Sales,
178 Rexdale
Boulevard,
Rexdale, Ontario,
Canada
M9W
1
R3.
13.
NWSA
booklet,
WELDING
SAFETY
BIBLIOGRAPHY
obtainable from the National
Welding
Supply
Association,
1900
Arch
Street,
Philadelphia,
PA
19103.
14.
American
Welding
Society
Standard AWSF4.1
Recommended
Safe Practices
for the
Prepara
tion for
Welding
and
Cutting
of
Containers
and
Piping
That Have Held Hazardous
Substances,
obtainable from the American
Welding Society,
550
Le Jeune
Rd.,
P.O.
Box
351040, Miami,
FL
33135.
15.
ANSI Standard Z88.2 Practice
for
Respiratory
Protection
obtainable
from the American Na
tional Standards
Institute,
1430
Broadway,
New
York,
NY 10018.
11.
CGA
Pamphlet
P-i,
SAFE HANDLING OF COM
PRESSED GASES IN CYLINDERS distribuØ
par
Ia
Compressed
Gas
Association,
500
Fifth
Avenue,
New
York,
NY
10036.
12.
CSA Standard
W117.2,
CODE FOR SAFETY
IN
WELDING AND CUTTING
distribuØ
par
Ia Cana
dian Standards
Association,
Standards
Sales,
178
Rexdale
Boulevard,
Rexdale,
Ontario,
Canada
M9W 1R3.
13.
NWSA
booklet,
WELDING
SAFETY
BIBLIOGRAPHY
distribuØ
par
a
National
Welding Supply
Association,
1900 Arch Street
Philadelphia,
PA
19103.
14.
American
Welding
Societe Standard AWSF4.1
Recommended
Safe Practices for
the
Prepara
tion for
Welding
and
Cutting
of Containers and
Piping
That Have Held Hazardous
Substances,
distribuØ
par
lAmerican
Welding
Societe,
550 Le
Jeune
Rd.,
P.O.
Box
351040, Miami,
FL
33135
15.
ANSI Standard
Z88.2 Practice
For
Respiratory
Protection
distribuØ
par
IAmerican
National
Standards
Institute,
1430
Broadway,
New
York,
NY 10018.
SECTION
2-
SAFETY PRECAUTIONS AND SIGNAL WORDS
2-1.
GENERAL INFORMATION AND SAFETY
A.
General
Information
presented
in this manual and
on
various
la
bels,
tags,
and
plates
on
the unit
pertains
to
equipment
design,
installation,
operation,
maintenance,
and
troubleshooting
which should be
read, understood,
and
followed for the
safe and effective
use
of this
equipment.
The
nameplate
of this unit
uses
international
symbols
for
labeling
the
front
panel
controls. The
symbols
also ap
pear
at
the
appropriate
section in the
text.
B.
Safety
The
installation, operation, maintenance,
and trouble
shooting
of
arc
welding
equipment requires practices
and
procedures
which
ensure
personal
safety
and the
safety
of others.
Therefore,
this
equipment
is to be in
stalled,
operated,
and maintained
only by qualified
per
Sons
in accordance with
this manual and all
applicable
codes such
as,
but
not
limited to, those listed
at
the end
of Section
1
Safety
Rules For
Operation
Of
Arc Weld
ing
Power Source.
2-2.
SAFETY
ALERT
SYMBOL
AND
SIGNAL
WORDS
The
following safety
alert
symbol
and
signal
words
are
used
throughout
this manual to call attention
to
and iden
tify
different
levels
of hazard
and
special
instructions.
a
This
safety
alert
symbol
is used with the
signal
words
WARNING
and
CAUTION
to call atten
tion
to the
safety
statements.
a
WARNING
statements
identify procedures
or
practices
which
must
be followed
to
avoid seri
ous
personal injury
or
loss
of life.
a
CAUTION
statements
identify
procedures
or
practices
which
must
be followed
to
avoid minor
personal
injury
or
damage
to this
equipment.
IMPORTANT
statements
identify
special
instructions
necessary for
the most
efficient
operation
of this equip
ment.
OM-1220
Page
12