- ページ 5

プールポンプ AquaPRO APB250UPROのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。AquaPRO APB250UPRO 12 ページ。 Aquapro systems swimming pool pump owner's manual

ページを印刷する

1. Replacement Parts List

Manual del usuario

Caudales de la bomba para piscinas

120

100

APB075PRO

0.75 HP

Caudales de la bomba para piscinas

100

APB100UPRO

1 HP

AquaPRO Systems

Carga total

Curvas características

60 ciclos 1 fase

3450 RPM

APB300PRO

3 HP

APB100PRO

1 HP

APB150PRO

APB200PRO

1.5 HP

2 HP

100

120

140

Caudal en USGPM

AquaPRO Systems

Sobre carga

Curvas características

60 ciclos 1 fase

3450 RPM

10/

APB250UPRO

2.5 HP

APB150UPRO

1.5 HP

APB200UPRO

2 HP

100

120

140

Caudal en USGPM

20 Sp

Electrical

A Ground Fault Circuit Interrupter (GFCI)

is required in the circuit. For size of GFCI

required and test procedures for GFCI,

see manufacturer's instructions.

• Never ground to a gas supply line.

• To avoid dangerous or fatal electrical

shock: turn OFF, disconnect the power

at its source, lock out power to motor,

and place a tag on the dedicated GFCI

circuit breaker indicating the power

is to remain OFF before working on

electrical connections.

Ground Fault Circuit Interrupter (GFCI) trip-

ping indicates an electrical problem. If GFCI

trips, determine the reason for tripping. If

you are uncertain, have a qualiﬁ ed electri-

cian inspect and repair the electrical system.

Verify supply voltage matches the nameplate

voltage. Incorrect voltage can cause ﬁ re or

seriously damage motor and voids warranty.

VOLTAGE

Voltage at motor must be within 10% of

the motor nameplate rated voltage or

motor may overheat, causing overload

160

tripping and reduced component life.

Verify voltage is correct before applying

power. If voltage does not fall within the

speciﬁ ed range during operation consult

the power company.

The pumps are shipped with motors

wired for 208-230 volt operation. The

3/4, 1 and 1-1/2 HP models are equipped

with a voltage change device for

115/208-230 operation. Refer to the mo-

tor nameplate for 115 Volt hook-up.

GROUNDING/BONDING

Install, ground, bond and wire motor

according to local or National Electrical

Code requirements. Permanently ground

the motor. Use ground terminal provided

in the terminal box on the back of the

motor. Use size and type wire required

by local codes. Connect motor ground

terminal to electrical service ground.

Bond motor to pool structure. Use a

solid copper conductor, size No. 8 AWG

or larger. Run wire from external bond-

ing lug to reinforcing rod or mesh.

Use solid copper bonding conductor not

smaller than 8 AWG (8.4 mm

accessible wire connector on the mo-

tor to all metal parts of the swimming

pool or spa structure and to all electrical

equipment, metal conduit, and metal

160

piping within 5 feet (1-1/2 m) of the in-

side walls of the swimming pool or spa.

APB075PRO, APB100PRO, APB150PRO, APB200PRO, APB300PRO,

APB100UPRO, APB150UPRO, APB200UPRO and APB250UPRO

WIRING

Follow all national and local wiring codes.

If unsure of code requirements consult a

professional electrician. Pump must be per-

manently connected to a dedicated circuit. If

unsure consult a licensed electrician.

NOTE: All electrical wiring and components

must be selected and installed in confor-

mance with the latest NEC requirements

and local codes. If you are unsure about the

requirements consult a licensed electrician

familiar with the requirements.

Operation

Do not run pump dry. Fill pump with

water before starting motor.

Before removing trap cover:

1. CLOSE GATE VALVES in suction and

discharge pipes

2. RELEASE ALL PRESSURE from pump

and piping system

If pump is being pressure tested, be

sure pressure has been released before

removing trap cover.

Do not block pump suction. To do so

with body may cause severe or fatal

injury. Small children using pool must

ALWAYS have close adult supervision.

Fire and burn hazard.

Motor runs at high

temperatures, to reduce the risk of ﬁ re,

do not allow debris, or foreign matter

to collect around the pump motor.

Allow motor to cool prior to handling or

performing maintenance.

The motor is equipped with an internal

thermal protection circuit to guard against

overheating. The maximum ambient

temperature for motor operation must not

exceed rating on motor model plate.

PRIMING PUMP

Release all pressure from ﬁ lter, pump,

and piping system; see the ﬁ lter owner's

manual. In a ﬂ ooded suction system (water

source higher than pump), pump will prime

automatically when suction and discharge

valves are opened. If pump is located above

the normal pool water level remove ring

and cover assembly and slowly ﬁ ll basket

and pump with water. Clean and inspect

o-ring; reinstall on trap. Replace ring and

cover assembly rotate clockwise to tighten

) from the

cover (see Figure 3).

Clamp ring must engage with pump body.

Push down and rotate until internal stops

are felt. Properly aligned tabs shown above

in Figure 3, assure lid is securely clamped.

Failure to tighten clamp ring as indicated

will reduce product strength, resulting in

failure of components, and bodily injury.

Pump prime time will

depend on vertical

distance and length of suction line. If pump

does not prime, make sure that all valves

are open, suction pipe is submerged. Verify

there are no leaks in suction lines. See

Troubleshooting Guide for further assistance.

Maintenance

All AquaPRO

Systems pumps are shipped

from the factory with DANGER and/or

WARNING labels already on the pump. These

labels contain a series of basic, yet extremely

important safety messages for the user and

bystander. Regardless of how well these la-

bels are attached or how scratch resistant or

wear-resistant they may be, it is possible that,

in time, the wording may become illegible

with normal use. Whenever you are repair-

ing the pump, performing routine mainte-

nance, or have the opportunity to inspect

the pump, make sure the label is readable.

If the label is not legible, replace the label

with an adhesive version that is available at

no charge by calling AquaPRO

Systems at

1-877-278-2797.

Use only parts supplied by manufacturer.

Similar looking parts may not have suf-

ﬁ cient strength for safe operation.

The only routine maintenance needed

is inspection/cleaning of strainer basket.

Debris or trash that collects in basket will

choke off water ﬂ ow through the pump.

Before attempting to clean basket:

A. Stop pump, disconnect power at its

source, lock out power, place tag on

the dedicated GFCI circuit breaker

indicating the power is to remain

OFF, close valves in suction and

discharge, and release pressure from

system.

Hazardous suction

can trap hair or body

parts, causing severe injury or death. Do

not block suction.

B. Remove ring and cover assembly by

turning counterclockwise. If necessary,

tap handles gently with a rubber mallet.

C. Remove basket and clean. Inspect

holes in basket for blockage. Clean

basket with water and replace in

basket housing. Verify basket is

oriented correctly in housing.

D. Clean and inspect lid o-ring; reinstall

ring and cover assembly.

E. Prime pump (see priming instructions).