- ページ 4

浄水器 Aquasafe Aquarium II Dual R.O./D.I. SystemのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Aquasafe Aquarium II Dual R.O./D.I. System 15 ページ。

ページを印刷する

5.1 Special note about braided wire plumbing

Braided wire plumbing

Figure 6

Braided undersink

plumbing. DO

NOT attempt to

Install onto this

Corrugated nylon tube

kind of plumbing.

proper seal needed. The inside of braided plumbing lines may vary and therefore may look differently

from this example. Don't let this confuse you. If the plumbing line is braided, DO NOT attempt to install

the feed water needed piercing valve to it. If you have this kind of plumbing there is usually a piece of

copper pipe that is located directly under your kitchen sink's faucet assembly which you can mount to

OR see our 3/8" x 3/8" x 1/4" plumbing adaptor on our website.

5.2 Installing the Needle Piecing Saddle Clamp to the cold water line.

Rotate the horizontal turning bar of the needle piercing valve to the left (counter clockwise) as you

do not want to pierce your cold water line at this stage. Make sure the needle is retracted all the way.

Next, clamp your cold water line TIGHTLY using the needle piercing saddle clamp which can be found

in your Large Parts Bag. (Fig. 7) You will need a Phillips screwdriver and small pair or pliers for this step.

home cold water shut o

Figure 7

Needle piercing

valve in place

on home's cold

water line.

red tubing

5.3 Connecting the feed water line to your system.

Next, take the 2-4 Inch piece of red tube from the Small Parts Bag and insert it into the elbow on the

"INLET" (left) side of the pre-filters (Fig. 8 - next page), then take the manual shut off valve, also found

in the Small Parts Bag, and attach it to the other end of the red tube (Fig. 8 - next page).

To more easily insert the tubing into the various fittings of your system it

TIP

is helpful to remove the blue "C" clip from around the collet and then in-

sert the tubing. After the tubing has been inserted into place, pull lightly

on the tubing in order to make room for the blue "C" clip and then place

the blue "C" clip back into its original position. The blue "C" clip holds the

collet in its proper position while the system is in operation.

page 4 | Maximus II Installation Instructions 05/13 | www.aquasafecanada.com

Please Note: DO NOT ATTEMPT

TO INSTALL THE NEEDLE PIERCING

WARNING

SADDLE CLAMP TO BRAIDED WIRE

PLUMBING (Fig. 6).

You can install the needle piercing saddle clamp to

all other forms of cold water lines found under the

common sink, just not the kind of plumbing de-

picted in Fig 6. The braided plumbing in Fig 6 is too

soft a material and will therefore not allow for the

Be sure to install above your

sink's shut off valve.

horizontal turning bar

DO NOT ATTACH TO THE HOT

WATER PIPE—AS HOT WATER

Needle piercing

WILL DAMAGE THE FILTERS

saddle clamp

WITHIN YOUR SYSTEM.

DO NOT PIERCE THE COLD

WATER LINE AT THIS

STAGE !

collet

blue

'C' Clip

Please make sure to FIRMLY push the tubing into the various fittings throughout this installation.

Now insert the needle piecing saddle clamp's red tubing into the other side of the Manual Shut Off

valve completing the feed water line pathway to your filtration system.

Insert 4 inch piece of

Figure 8

red tubing into elbow

on "water inlet" side of

Complete the

Cap

pre- lter housing

feed water

pathway to your

system by

red tubing

elbow

following the

diagram

"water inlet"

(left) side

(1st pre lter

Side

housing)

view

5.4 Piercing the cold water line

Ensuring the needle piecing saddle clamp is firmly in place, screw down the needle of the saddle

clamp using the horizontal bar on top of the clamp.

Note: You will feel resistance when the needle is piercing the cold water line, so pay attention to the

amount of resistance experienced. This resistance will stop when you have successfully pierced the

cold water line. CAUTION: Do not screw in the needle valve to its maximum depth as you then risk

piercing the opposite side of your cold water line.

After the cold water line has been pierced, turn the horizontal bar on the top of the clamp counter

clockwise (left) until it becomes snug. This retracts the piercing needle creating a path for feed water

to flow into the red tubing – supplying your system with its feed water.

PLEASE NOTE: Do not turn your home's emergency cold water shut off back to its ON position yet!

5.5 Flushing of the Pre-filters

Figure 9

www.aquasafecanada.com

Flushing the

pre-filters

manual

shut o

valve

This will allow for the water to flow through the three pre-filters and then into your kitchen sink, flush-

ing out any and all loose particulates and carbon dust thereby preventing these initial loose particu-

lates from reaching the 4th stage (Reverse Osmosis Membrane) ensuring the maximum life span of the

Reverse Osmosis Membrane.

www.aquasafecanada.com | Maximus II Installation Instructions 05/13 | page 5

Manual shut

o valve

red tubing

leads to needle

piercing saddle

clamp which

red tubing

is attached to

your home's

cold water line

Attach shut

Attach the

o valve to

long red

red tubing

tubing to other

side of shut

o valve

Found in your Large Parts

Bag is a coiled length of blue

tubing. Uncoil the tubing

and insert one end into

the "OUTPUT" elbow (right

side) of the three pre-filters

and place the other end of

the blue tubing into your

kitchen sink. (Fig 9)