- ページ 5

キッチン家電 Diamond +7ECEH4R00のPDF マニュアルをオンラインで閲覧またはダウンロードできます。Diamond +7ECEH4R00 13 ページ。
Diamond +7ECEH4R00 にも: マニュアル (13 ページ), 取扱説明書 (13 ページ)

IV. THE ENVIRONMENT

1. PACKING

Packing materials are environment friendly and can
be stored without risk, or burned in a special waste
incineration plant.
Recyclable plastic components are marked with:
Polyethylene: outer wrapping, instruction booklet
bag, gas nozzle bag.
Polypropylene: roof packing panels, straps.
PP
Polystyrene foam: corner protectors.
PS

2. USE

Our appliances offer high performance and efficiency. To re-
duce consumption of electricity, water or gas, do not use the
appliance empty or in conditions that compromise optimal
efficiency (e.g. with doors or lids open, etc.); the appliance is
used in a well-ventilated place to avoid the creation of
dangerous mixtures of unburnt gases in the room. Whenever
possible, pre-heat only before use.

3. CLEANING

In order to reduce the emission of pollutants into the
environment, clean the appliance (externally and when
necessary internally) with products that are more than 90%
biodegradable (for further information, see chap. V
"CLEANING").

4. DISPOSAL

Do not disperse in the environment. Our
appliances are manufactured using more
than 90% (in weight) recyclable metals
(stainless steel, iron, aluminium, galvanised
sheet, copper, etc.).
Make the appliance unusable by removing
the power cable and any compartment or cavity closing
mechanisms (when present) in order to avoid the risk of
someone becoming closed inside.
V. INSTALLATION
Carefully read the installation and maintenance
procedures given in this instruction manual before
installing the appliance.
• Installation, maintenance and conversion to
another type of gas must only be carried out by
qualified personnel authorised by the
manufacturer.
Failure to observe the correct appliance installation,
conversion and modification procedures can cause
damage to the appliance, danger to persons and
invalidates the Manufacturer's warranty.

1. REFERENCE STANDARDS

• Install the appliance in accordance with the safety
regulations and local laws of the country where used.
• AUSTRALIA: this appliance shall be installed only by
authorised persons and in accordance with the
manufacturer's installation instructions, local gas fitting
regulations,municipal building codes, electrical wiring
regulations, local water supply regulations, AS5601-gas
installation, health authorites and any other statutory
regulations.

2. UNPACKING

IMPORTANT!
Immediately check for any damage caused during
transport.
• The forwarder is responsible for the goods during transport
and delivery.
• Inspect the packing before and after unloading.
• Make a complaint to the forwarder in case of visible or
hidden damage, reporting any damage or shortages on
the dispatch note on delivery.
• The driver must sign the dispatch note: The forwarder can
reject the claim if the dispatch note is not signed (the
forwarder can provide the necessary form).
• Unpack, taking care not to damage the
equipment. Wear protective gloves.
• Carefully remove the protective film from metal surfaces
and clean any traces of glue with a suitable solvent.
• For hidden damage or shortages becoming apparent only
after unpacking, request the forwarder for inspection of
the goods within and not later than 15 days of delivery.
• Keep all the documentation contained in the packing.

3. POSITIONING

• Handle the equipment with care in order to avoid damage
or danger to persons. Use a pallet for handling and
positioning.
• The installation diagram given in this instruction manual
gives the appliance dimensions and the position of
connections (gas, electricity, water). Check that they are
available and ready for making all the necessary
connections.
• The appliance can be installed separately or combined
with other appliances of the same range.
• The appliances are not designed for built-in installation.
Leave at least 10 cm between the appliance and side or
rear non-combustible walls.
Leave at least 25 cm between the appliance and side or
rear walls made from combustible materials.
• Suitably insulate surfaces that are at distances less than
those recommended.
• Maintain an adequate distance between the appliance and
any combustible walls. Do not store or use flammable
materials and liquids near the appliance.
• Leave an adequate space between the appliance and any
side walls in order to enable subsequent servicing or
maintenance operations.
• Check and if necessary level the appliance after
positioning. Incorrect levelling of the appliance can affect
combustion and cause malfunctioning.
19