水ポンプ AquaScape 91045のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。AquaScape 91045 2 ページ。
ページを印刷するI N S T A L L A T I O N
ULTRA PUMP
FOUNTAIN HEAD KIT
Small Ultra Pump
Fountain Head Kit
Item #91045
Contents
No.
Description
1.
Diverter Valve Assembly
2.
Fountain Riser Stems
3.
Foaming Jet Fountain Head
4.
Waterbell Fountain Head
5.
Daisy Fountain Head
3
4
Safety Information
WARNING: To provide continued protection against risk of
electric shock, be sure the fountain pump is connected to
a properly grounded, ground fault circuit interrupter (GFCI)
outlet. Always follow the safety instructions for the pump you
will be using.
Ultra Pump Fountain Head Kit Specs
Fountain Head
Pump Sizes
Kit Needed
Spray Diameter
Ultra 400
91045
Ultra 550
91045
Ultra 800
91045
Ultra 1100
91046
Ultra 1500
91046
Ultra 2000
91046
Installation
ASSEMBLING THE ULTRA PUMP WITH FOUNTAIN HEAD FITTINGS
• Unpack the diverter valve and thread it
clockwise directly into the pump discharge
opening (Ex. 1). Do not use tools or over
tighten.
• The diverter valve has two flow-control
valves (Ex. 2):
1. The accessory diverter valve controls
water flow to any additional filters,
fountains, or waterfalls
2. Side valve controls water flow to attached fountain head
Large Ultra Pump
Fountain Head Kit
Item #91046
2
1
5
Waterbell
Foaming Jet
Daisy
Spray Height
Spray Height
up to 12"
up to 12"
up to 40"
up to 15"
up to 16"
up to 47"
up to 21"
up to 18"
up to 52"
up to 31"
up to 20"
up to 76"
up to 34"
up to 22"
up to 86"
up to 36"
up to 24"
up to 96"
facebook.com/aquascapeinc
youtube.com/aquascape4
pinterest.com/aquascapeinc
instagram.com/aquascape_inc
I N S T R U C T I O N S
• The side
valve controls
the fountain
height, but the
accessory valve
will also have
an effect on
the fountain's
height. As more
accessory flow
is desired, the amount of water flowing to the
fountain will diminish. Closing the accessory
valve will maximize flow to the fountain head.
• Thread the riser stem base onto discharge.
Riser stems can be added to the base stem
as-desired to increase the fountain height to the best level for your water
feature (Ex. 3).
• Install any one of the three fountain heads onto the top riser by simply
pressing it over the end of the riser. It is held in place by friction.
• The Ultra Pump
Fountain Head
Kit is designed
to be submerged
directly into
the pond or
decorative
fountain container.
If using the
diverter valve to
supply a pond
filter, locate the
pump as far as possible from the location of the water entering back into
the water feature, in order to maximize pond circulation (Ex. 4).
USING DIVERTER TO OPERATE ADDITIONAL ACCESSORIES
• Attach tubing to the diverter fitting (Ex. 5). If
tubing is loose on fitting, use a hose clamp
(not included) to secure.
• Connect the other end of the pump tubing
to the pond filter, pressurized filter, waterfall
spillway, or to a decorative fountain or spitter.
• Connect the Ultra pump to an outlet that
is protected by a ground fault interrupter
(GFCI). Once the pump is running and water
is circulating throught the filter(s) or waterfall, check for any fitting or
waterfall leaks where the external connections are made.
General Maintenance
• The height of the fountain is determined by several factors:
– Pump size, as estimated in the earlier table
– How deep the pump is positioned in the water; lowering the pump
increases the flow since the discharge is also lowered
– The two valve adjustments on the diverter valve (see information
above)
• To maintain the correct flow and fountain head patterns, both the
fountain heads and the pump screens will require occasional cleaning.
Troubleshooting
• Reduced water flow
– The fountain head itself may be clogged. Shut off the pump, and
remove the head for a more thorough
cleaning with a garden hose and brush.
– The fountain heads can be thoroughly
cleaned, if needed, by taking them apart
(Ex. 6).
• Pump or plumbing may be clogged
– Clean the pump cage screens, filter
Ex. 1
sponges, and/or impeller.
– Adjust the diverter valve(s) to set the
desired flow to the fountain and/or accessory.
For more information about our company or products, please visit our website at
aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426
©2022 Aquascape, Inc. • All Worldwide Rights Reserved
1.
2.
Insert additional
Riser Stems
and lock into
position
Ex. 2
Thread Riser
Stem Base onto
discharge
Ex. 3
Ex. 4
Ex. 5
Ex. 6
04/22