- ページ 4

水ポンプ AquaScape 91104のPDF インストラクションとメンテナンスをオンラインで閲覧またはダウンロードできます。AquaScape 91104 9 ページ。 Adjustable flow solids-handling pond pump
AquaScape 91104 にも：使い方とメンテナンス (20 ページ), インストラクションとメンテナンス (16 ページ)

ページを印刷する

sufficient oxygen levels and proper

gas exchange in the pond, helping

to prevent fish loss. For best results

use the AquaForce

in combination

with a de-icer. The combination of

the AquaForce

pump and a pond

de-icer will further increase the

Pond De-Icer (#39000)

pond's oxygen levels and remove

potentially harmful gases from the water, as well as allow

for a back-up in case one of the devices stops working.

• It is important to not place the AquaForce

on the bottom

of the pond during the winter, which may disrupt the

natural thermocline found in the deeper portions of the

pond where the fish overwinter. Instead, place the pump

at least one foot above the

deepest point of the pond. The

rotational ball should be turned

upwards, allowing the water

to bubble at the surface of the

pond. Bricks or stones can be

used, if needed, to raise the

pump to the proper level.

Remote Control and Receiver

Operation

• Receiver Switch – The Receiver includes

a switch that allows the pump to be operated

in the two following modes:

Position 1 - Operated by Remote Control

Position 2 - Bypass the Remote and

–

operate at full flow-rate

In the event of a power loss when operating in the Remote

Control setting, the pump will revert to its most recent flow-rate

setting.

• Remote Control – The Remote Control includes the ability

to turn the pump on and off, as well as adjust the flow of

the pump. Make sure the switch on the Receiver is in the

Remote Control setting in order for the Remote to work

properly. The Remote Control has an approximate range of

150 feet. The range of the Remote may be reduced if there

are obstacles between the Remote and Receiver. Use the

included mounting holster provided to provide a location

to store the remote control. It is recommended to mount

the holster in an area that is protected from the outdoor

elements.

☎

PLEASE NOTE: The Remote

Control and Receiver are

paired together with their

own unique frequency. For

this reason Remote Control

replacement kits include both

Remote Control and Receiver.

• Battery Installation

1. Remove 4 screws and back cover plate.

2. Place battery into the battery compartment.

Requires 1- 23A 12V battery.

3. Replace back cover and install screws.

Pump Operation and Maintenance

• Pump Cage – Do not remove the upper or

lower pump cage while operating the pump.

Failure to operate the pump without the filter

cage or operating the pump with

a broken cage will allow large

debris to enter the pump, causing

TROUBLESHOOTING TIPS

the pump to fail and voiding the

warranty.

• Pump Cage Cleaning –

We recommend inspecting

your pump on a regular basis to

ensure it is functioning properly.

If you notice the flow-rate

diminish, it may be due to the

pump's filter cage becoming

clogged with debris. In many

cases, the pump can simply

be pulled from the pond for

cleaning. Remove any debris

stuck to the pump filter cage

and/or use a garden hose to

spray the cage clean. Always

disconnect the power prior to

performing maintenance on the

pump.

• Remove any debris stuck to the

pump filter cage and/or use a

garden hose to spray the filter

cage clean.

US 1-866-877-6637 |

☎

CAN 1-866-766-3426 | www.aquascapeinc.com

• Internal Pump Cleaning – If you have thoroughly

cleaned the filter cage screens and still have diminished

Decrease

flow rates, then you will need to remove the pump from

Flow

the lower cage and inspect the impeller rotor assembly.

Increase Flow

• Pull the cage release tabs outward to unlock the upper

On/Off

and lower pump cages.

• With the cage tabs released, the upper filter cage can be

lifted to expose the pump.

VIDEO ON AQUAFORCE

PUMP MAINTENANCE &

• Remove the screws

securing the pump

restraining bracket,

allowing the pump to be

lifted from the lower cage.

www.aquascapeinc.com |

• Remove the four screws that hold the water cover

chamber and inspect the impeller rotor assembly.

• If your rotor assembly impeller and internal pump body

have excessive scale build-up, clean with a mild acid,

such as white vinegar or non-abrasive calcium, lime and

rust remover product. A sponge or soft-bristled brush that

won't scratch the stainless steel can be used at this time.

Removing scale build-up will allow your pump to run like

new again.

Replacing the Impeller/Rotor Assembly

When replacing the

AquaForce

rotor-impeller

assembly into the pump

chamber, note the proper

orientation. The raised key

on the impeller face plate

should be lined up with the

groove in the pump housing.

PUMP FLANGE PIN

• AquaForce

ready for reassembly – The water chamber

cover will only fit back onto the pump with the top of the

tear-drop shapes lining up, along with matching the hole in

the cover with the pin on the face of the pump motor flange.

• For easier pump access,

pull the power cord free

from the strain relief.

PUMP

FLANGE PIN

☎

CAN 1-866-766-3426 |

☎

US 1-866-877-6637

GROOVE

RAISED KEY

PUMP WATER

COVER HOLE

PUMP WATER

COVER HOLE