- ページ 6
デジタルカメラ Panasonic AW-HEA10WEJのPDF 据付・取扱説明書をオンラインで閲覧またはダウンロードできます。Panasonic AW-HEA10WEJ 40 ページ。 Control assist cameras
Panasonic AW-HEA10WEJ にも： 取扱説明書 (34 ページ)
ページを印刷する
Installation precautions (continued)
Before installation, always disconnect the power
plug.
When installing, always use the supplied components.
Do not disassemble or modify the wall mount adaptor.
Tightening up the mounting screws
• Tighten up the screws and bolts securely to the degree that is
appropriate for each of the materials used in the mounting location
and structures.
• After tightening up the screws and bolts, check that there is no
unsteadiness and that the parts have been tightened securely.
• Use the specified tools to firmly tighten the screws to the
specified tightening torques.
Screw
Tightening torque
diameter
M3
0.78 N · m {8 kgf · cm}
M4
1.47 N · m {15 kgf · cm}
• Tighten up the screws using the specified torque driver. Do not
use electrical drivers or impact drivers.
When the unit is no longer going to be used, do
not leave it lying around, but be absolutely sure
to dispose of it properly.
For details on how to remove the unit, refer to "How to remove the
camera" (→ page 17).
Do not attach a filter, hood, extender or other
parts to the unit.
Use the dedicated AC adaptor and power cable
provided with the unit.
Connect the AC adaptor and power cable to the power inlet
securely.
Installing the AC adaptor
• Do not place the AC adaptor directly onto the ceiling panel or
other such surface. Extreme danger is posed when water has
collected on the surface as a result of leaking rain, for instance.
Secure the adaptor firmly to the bottom or other surface of a
reinforcing member made of channel steel where dust and other
foreign matter will not accumulate.
(→page 12)
• Secure the adaptor firmly so that there will be no chance that it will
fall off or fall down. Secure it using a strength which can withstand
the mass (approx. 0.3 kg (0.66 lb)) of the AC adaptor.
Adjusting the shooting range
You can manually adjust the pan (approximately 45° left and right) and tilt (approximately 30° up and down) for the lens of the unit.
Adjust the shooting range depending on the installation location.
Left:
Approx. 45°
Up and down:
Approx. 30°
6
Angle of view:
Approx. 95°
Right:
Approx. 45°
Install the accessory AC adaptor near the main
power outlet, and position it in such a way
that its power plug can be plugged into and
unplugged from the outlet easily.
When connecting the AC adaptor to a power outlet on the ceiling or
on any other surface where dust may collect, wipe off the dust on
the power plug at periodic intervals as an anti-tracking measure.
Connecting the power cable
Be absolutely sure to connect the power cable of the AC adaptor
through a circuit breaker using one of the following methods.
(1) Connect the power cable through a power control unit.
(2) C onnect the power cable to a circuit breaker in a power
distribution panel with a contact distance of 3.0 mm (1/8
inches) or more.
Use a circuit breaker which is capable of shutting off all the
poles of the main power supply with the exception of the
protective ground conductor.
(3) I nstall the AC adaptor near the power outlet, and connect it
through the power plug.
If there is a possibility of noise interference
Wire the cables so that the power cable (ceiling light cord) of AC
100 V
(AC 220 V
) or more, and the signal cable are placed at
*
1
*
2
least 1 meter (3.3 ft) apart.
Alternatively, run each cable through its own metal conduit. (The
metal conduits must be grounded.)
For AW-HEA10WPJ, AW-HEA10KPJ
*
1
2
For AW-HEA10WEJ, AW-HEA10KEJ
*
Radio signal interference
If the unit is positioned near a TV or radio transmitting antenna or a
strong electrical field or magnetic field (such as that generated by a
motor, transformer or power lines), its images may be distorted and/
or the images may be affected by noise.
When connecting the cables, ensure that the
connector areas will not be subject to any load.
Doing so may cause malfunctioning.
PoE power supplies
Use a PoE (IEEE802.af) compatible hub or power supply device.
Angle of view:
Approx. 95°