- ページ 2

水ポンプ Aquatec Equipment Aquapro AP1050/CのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Aquatec Equipment Aquapro AP1050/C 2 ページ。 Waterfeature pumps

ページを印刷する

Congratulations on your purchase of this product by AquaPro,

the answers for your watergarden made easy!

AP550

VOLTAGE (V)

240

POWER (WATTS)

10.5

MAX HEIGHT (M)

1.10

FLOW MAX (L/H)

550

CABLE LENGTH (M)

13mm

DESCRIPTION AND FEATURES

Your Aquapro solar pump has been

manufactured with advanced technology to

provide you with the best quality system

for your pond or water feature.

• Aquapro pumps are suitable for use in

many different applications including;

fountains, water features, small ponds

and hydroponics.

• Your Aquapro pump has a single moving

part (an impellor set) therefore enabling

easy cleaning and maintenance.

• The motor and electrical components are

encapsulated in epoxy resin, ensuring

safe operation under water.

• The pump has a robust bearing and shaft

design so no oil/grease lubrication is

required.

• The Aquapro pumps that have plastic

encased impellor parts and ceramic

shafts (no exposed metal) may be used

in salt water applications.

• The Aquapro No1 fountain kit suits most

models of small Aquapro pumps.

• Check out the Aquapro range of pond

lights and accessories.

AP750

AP1050/C

AP1350

240

1.50

1.80

2.80

750

1050

1350

13mm

INSTALLATION

1. If required, have a qualiﬁed electrician

install weatherproof power point near

to the pond or water feature, (within the

cable length of the pump).

2. Place the pump in desired location,

ensure the pump is on a stable surface

that is free of sludge, sand and other

debris, and connect tubing to the outlet

or attach fountain kit.

3. Ensure pump is submerged, then plug

in power cord and switch on.

MAINTENANCE

Disconnect power cord from the power

supply before performing maintenance.

Never lift the pump by the power cord.

The only serviceable item is the impellor

set. The motor unit of the pump is

encapsulated with epoxy resin and does

not need lubrication.

All Aquapro submersible pumps are water

cooled; if pump becomes restricted it

will overheat and could cause permanent

damage. Ensure pump does not become

blocked or restricted.

SUBMERSIBLE WATERFEATURE PUMPS

The power cord cannot be replaced.

If the cord is damaged, the pump must

be discarded.

The impellor set is a wearing consumable

part. Regular inspections, cleaning and

maintenance of impellor is necessary to

ensure longer impellor life.

If the impellor set becomes worn or

damaged it should be replaced (available

from your dealer or special orders). Failure to

do so may cause serious damage to pump.

1. Disconnect the power cord from

the power supply before performing

maintenance.

2. Remove from water, detach tubing/

fountain kit and remove front cage

from pump.

3. Remove the impellor cover by

either turning anti-clockwise and pulling

out or pulling tab to unclip (depending

on model).

1 Motor & Casing

2 Impellor

3 Impellor Cover

4 Front Cage

AP750 Model shown. Picture for illustration purposes only.

INSTRUCTIONS MANUAL

4. Gently remove the impellor and shaft,

use long nose pliers if needed. Take

care not to break ceramic shaft (if

applicable) because they are brittle.

5. Clean impellor, checking for any signs of

wear or damage.

6. Reinstall the shaft, and then carefully

slide the impellor onto the shaft. The

impellor will pull itself in by magnetic

force, this is normal (take care not to

pinch your ﬁngers).

7 . Replace the impellor cover making sure

the shaft is located properly on the

impellor cover.

8. Replace the front cage.

9. Re-attach tubing/fountain kit, submerse

in water, connect to power supply and

turn on.