- ページ 15

スイッチ HP XP20000/XP24000のPDF 設定マニュアルをオンラインで閲覧またはダウンロードできます。HP XP20000/XP24000 44 ページ。 Hp storageworks xp disk array configuration guide: vmware (a5951-96106, september 2010)
HP XP20000/XP24000 にも： リリースノート (13 ページ), 統合マニュアル (29 ページ), リリースノート (4 ページ), 管理者マニュアル (50 ページ), 設定マニュアル (42 ページ), 設定マニュアル (40 ページ), 設定マニュアル (40 ページ), 設定マニュアル (36 ページ), 設定マニュアル (36 ページ), 設定マニュアル (30 ページ), 設定マニュアル (36 ページ), リリースノート (5 ページ), 設定マニュアル (46 ページ), 設定マニュアル (46 ページ), リファレンス・マニュアル (46 ページ), 設定マニュアル (40 ページ), 設定マニュアル (38 ページ), 設定マニュアル (34 ページ), 設定マニュアル (30 ページ), 設定マニュアル (30 ページ)

ページを印刷する
HP XP20000/XP24000 設定マニュアル
Within the SAN, the clusters must be homogeneous (all the same operating system). Heterogeneous
(mixed operating systems) clusters are not allowed. How you configure LUN security and fabric zoning
depends on the SAN configuration.

Fabric zoning and LUN security for multiple operating systems

You can connect multiple clusters with multiple operating systems to the same switch and fabric using
appropriate zoning and LUN security as follows:
Storage port zones can overlap if more than one operating system needs to share an array port.
Heterogeneous operating systems can share an array port if you set the appropriate host group
and mode. All others must connect to a dedicated array port.
Use LUN Manager for LUN isolation when multiple hosts connect through a shared array port.
LUN Manager provides LUN security by allowing you to restrict which LUNs each host can access.
Table 2 Fabric zoning and LUN security settings
Environment
Standalone SAN
(non-clustered)
Clustered SAN
Multi-Cluster SAN

Connecting the disk array

The HP service representative performs the following steps to connect the disk array to the host:
1.
Verifying operational status of the disk array channel adapters, LDEVs, and paths.
2.
Connecting the Fibre Channel cables between the disk array and the fabric switch or host.
3.
Verifying the ready status of the disk array and peripherals.

Verifying new device recognition

To verify that the NetWare system recognizes the new disk array devices:
1.
In the NetWare directory, enter SERVER to get to the server console.
2.
At the server console, enter LIST DEVICES to display all devices. Use the Pause key as needed.
The device number (for example, 0x000B) and device type are displayed for each device:
Example
NetWare prompt>
1. 0x000B: [V6E0-A2-D7D:0] HP OPEN-3 rev:0111
2. 0x000C: [V6E0-A2-D7D:1] HP OPEN-3 rev:0111
:
:
3.
Record the device number for each new device on the worksheet in
This information will be useful later during disk partitioning and volume creation.
4.
Verify that all new disk devices are listed.
OS Mix
homogeneous (a single OS type
present in the SAN)
heterogeneous (more than one OS
type present in the SAN)
LIST DEVICES
XP Disk Array Configuration Guide: Novell NetWare
Fabric Zoning
Must be used when mul-
Not required
tiple hosts or cluster
nodes connect through
Required
a shared port
"Path
Worksheet" on page 31.
LUN Security
15