- ページ 9

ステレオシステム Panasonic RX-C52のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Panasonic RX-C52 21 ページ。 Portable stereo component system

ページを印刷する

TAPE PLAYBACK

1) Open the Cassette Compartment cover by pressing the

Eject Button. Insert the cassette as shown in the figure,

and then close the Cassette Compartment cover.

Full reel of tape

Note:

Make sure the exposed part of the cassette tape is

face

down.

If it is upside

down,

the

Cassette

Compartment cannot be closed, do not try to force it

shut.

2) Press the Power Switch to "= ON".

eThe Power/Battery Check Indicator will light.

3) Press the TAPE

Button (FUNCTION).

4) Set the Tape Selector, as shown in the table below,

according to the cassette tape used.

Tape Selector Settings

am.

|METAL

High bias chromium tape

or equivalent

# NORMAL

Low bias ferric oxide tape

5) Set the Dolby Noise Reduction Switch to "m= IN" to

playback a tape recorded with Dolby Noise Reduction.

For other tapes, set the switch to "i OUT".

eThe Dolby Noise Reduction Indicator will light if the

Dolby Noise Reduction Switch is set the switch to ''m

IN".

6) Press the Tape Direction Button to the desired mode.

: Non-reverse mode

: Auto reverse mode

C=) : Auto-continuous mode

(Refer to page 11 "Auto-Reverse Playback".)

7) Press the Forward Button to begin tape playback.

eThe Forward Indicator will light.

(Press the Power Switch to "Ml OFF/SLEEP"

when

you want the power

automatically turned off upon

completion of tape playback.)

8) Adjust the Volume, Balance, Bass and Treble Controls.

9) To stop the playback, press the Stop Button.

10) Press the Power Switch to 'i OFF/SLEEP"" to turn the

unit off.

@ Full Auto-Stop Mechanism

During playback, recording, fast forward, or rewind when the

tape comes to its end, the tape travel wiil automatically stop.

However, as shown in the table below, if the Tape Direction

Button is set to ' C)" the Auto-Stop mechanism will not

operate.

OPERATION

ise

PLAYBACK

RECORDING

TAPE

DIRECTION

Note:

If the Power Switch is 'm= ON", the power to the unit

of al

(eae

recording of)

sides

both sides

YES

Berignte

recording

both sides

will not be turned

off even

after the Auto-Stop

mechanism has operated. In this case, be sure to set

the switch to '' OFF/SLEEP" to turn off the power.

@ Rewind Auto Play

The rewind auto play function allows you to easily and

automatically listen to a tape from its beginning.

eDuring

forward

playback; While

holding the Forward

Button pressed, press the TPS/Rewind Button {the For-

ward Indicator will flash].

eDuring

reverse

playback;

While

holding the

Reverse

Button pressed, press the Fast Forward/TPS Button [the

Reverse Indicator will flash).

The tape will be automatically rewound to its beginning, and

playback will begin.

@ Dolby NR

This unit includes Dolby Noise Reduction which reduces

tape noise to a remarkable degree.

Briefly, the system works as follows:

At low sound levels (where tape noise is most noticeable),

the high frequency (treble) portion of the sound is recorded

at a higher level.

During playback, the same high frequency portion of the

sound is played back at a lower level. Since tape noise is

introduced during recording and consists mainly of high

frequencies, the tape noise is also reduced during playback.

In effect, the sound is boosted during recording, then the

sound along with the tape noise is reduced during playback.

The result is unaltered sound with reduced tape noise.

eTape Counter and Reset Button

The digits return to "000" when the Reset Button is pressed.

The digits advance with the tape to provide a reference to

quickly find a desired portion of the tape.

R a

aT Oa RP

TE ST Reh

rE MP eT OP on te RE