- ページ 2

ヒーター Bionaire BCH4267のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bionaire BCH4267 2 ページ。 Twin ceramic heater
Bionaire BCH4267 にも：取扱説明書 (12 ページ), 取扱説明書 (2 ページ)

ページを印刷する

BCH4267IUK07EM1.qxd

10/9/07

22:25

Page 4

BCH4267

Fig. 1

Fig. 2

ENGLISH

DESCRIPTION

A. Thermostat Control

B. Selector Control/ Mode

HI (II) LO (I) OFF (O)

C. Power Indicator Light

OPERATING INSTRUCTIONS

Setting the Power Level

1. For heater operation, turn Thermostat Control

(A) to HI (

) (See Figure 2).

2. Turn Selector Control (B) to II or I.

NOTE: Power Indicator Light (C) will illuminate

when heater is plugged into the mains.

Setting the Thermostat

The thermostat maintains the desired

temperature level by switching on and off.

1. Turn the Thermostat Control all the way to

the right (clockwise) to the maximum

temperature level HI (

2. When the desired temperature is reached,

slowly turn the Temperature Control back

(counter-clockwise) until the heater switches off.

3. The control will now automatically maintain

the pre-set temperature level by turning the

heater ON and OFF.

4. The Power Indicator Light will remain lit to

indicate the heater in on.

NOTE: It is normal for the heater to cycle ON

and OFF as it maintains the preset temperature.

To prevent the unit from cycling, you need to

change the thermostat setting.

FROST-GUARD SETTING

This special setting will automatically turn on the

heater if the room's temperature reaches freezing.

To set, turn the Thermostat Control all the way

to LO (

), and turn the Selector Control to either

HI (II) or LO (I).

COLOUR CHANGING DISPLAY

Your heater features the revolutionary

technology and safety of Colour Changing

Display. As your heater warms up, parts of, the

front grill will change colour – a visual reminder

that the grill is warm and the heater is on. The

exact timing of the colour change may vary.

When the heater is turned off, the grill will return

to its original colour , thus indicating the grill is

cool to the touch. This may take up to an hour

depending on the environment surrounding the

heater and the cooling down time of the

element.

NOTE: If left in extreme cold temperatures

6. Under the environment with electrical fast

(-22° F/-30°C) the Colour Changing Display may

transient, the product may malfunction and

not perform. The heater itself will function

require user to reset the product.

normally. Store heater in a cool and dry location.

7. Do not use this heater with a programmer,

NOTE: The colour changing effect may wear off

timer or any other device that switches the

after continuous, heavy use of the heater or in

heater on automatically, since a fire risk exists if

time. The heater will continue to operate

the heater is covered or positioned incorrectly.

normally.

8. Only touch the heater with dry hands.

9. DO NOT position where it can be touched by

AUTO SAFETY SHUT-OFF

children, especially the very young.

This heater is equipped with a technologically-

10.DO NOT use this heater outdoors.

advanced, safety system that requires the user

11. Allow a safe area around the heater away

to reset the heater if there is a potential overheat

from furniture or other objects; at least 50 cm

situation. When a potential overheat temperature

from the top and sides and 200 cm at the front.

is reached, the system will automatically shut

the heater off. It can only resume operation

12.Do not use this heater when it is lying on its side.

when the user resets the unit.

13.DO NOT use the heater in rooms with

explosive gas (e.g. petrol) or while using

To Reset the Heater:

inflammable glue or solvent (e.g. when gluing

1. Turn MODE to (O) and Thermostat to HI (

or varnishing parquet floors, PVC etc.).

2. Unplug unit, wait 30 minutes.

14.DO NOT insert any objects into the heater.

3. Plug in and turn ON.

15.Keep the mains cord at a safe distance from

Safety Back-Up Fuse

the main body of the heater.

In the unlikely case the heater does not respond to

16.If overheating should occur, the built-in

an overheat situation, the safety back-up fuse will

overheating safety device will switch off the

engage. In this case, the heater will not reset.

heater.

Please contact your local service number on the

17.Do not place the cord under a rug.

back of the manual for advice.

18.The heater is to be installed so that switches

and other controls cannot be touched by a

PLEASE READ AND SAVE THESE

person in the bath.

IMPORTANT INSTRUCTIONS

19.Avoid the use of an extension cord because

When using electrical appliances, basic safety

it may cause the heater to overheat.

precautions should always be taken including

20.This appliance is not intended for use by

the following:

persons (including children) with reduced

1. Before connecting the heater, check that the

physical, sensory or mental capabilities, or lack

voltage indicated on the rating plate

of experience and knowledge, unless they

corresponds to the main voltage in your

have been given supervision or instruction

home/office.

concerning use of the appliance by a person

2. WARNING: In order to avoid overheating, do

responsible for their safety. Children should be

not cover the heater (

supervised to ensure that they do not play with

3. DO NOT position the heater directly under a

the appliance.

power socket.

4. Do not use this heater in the immediate

surroundings of a bath, a shower or a

swimming pool.

5. If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its

service agent or similarly qualified person in

order to avoid hazard. The heater contains

no user serviceable parts. Should the product

suffer damage or breakdown, it must be returned

to the manufacturer or their service agent.

For U.K. and Ireland only:

If the plug is not suitable for the socket outlets in

your home, it can be removed and replaced by

a plug of the correct type. Please refer to

"Installation of a plug" below.

Installation of a plug Applicable to

U.K. and Ireland

This product is fitted with a 13A plug complying to

BS1363. If this plug is unsuitable or needs to be

replaced, please note the following:

The wires in the mains lead are coloured as

such:

BROWN

LIVE

BLUE

NEUTRAL

Please note that the colour of these mains wires

may not correspond with the colour markings

that identify the terminals in your plug. Please

proceed as follows:

The BROWN coloured wire must be connected

to the terminal, which is marked with the letter

"L" or is coloured RED.

The BLUE coloured wire must be connected to

the terminal, which is marked with the letter "N"

or is coloured BLACK.

DO NOT CONNECT either of these wires to the

earth terminal in the plug. The earth terminal plug

is marked with the letter "E", or with the earth

symbol

or coloured GREEN and YELLOW.

NOTE: If the terminals in the plug are not

marked or if you are unsure or in doubt about

the installation of the plug please contact a

qualified electrician. If a 13A 3-pin plug is fitted,

it must be an ASTA approved plug, conforming

to BS1363 standard. Replacement 13A fuses

must be BSI or ASTA BS1362 approved.