- ページ 3
カッター Alpha Professional Tools ECC-TABLEのPDF テクニカル・ノートをオンラインで閲覧またはダウンロードできます。Alpha Professional Tools ECC-TABLE 4 ページ。 Dry tile cutting system
What kind of blades can I use on my ECC-125/225?
The following can be used as dry applications only.
WITH Ecocutter Table and Stand:
o
Eclipse: DEE005, DEE045
o
Katana: DPT125, DPT115
o
Libero: DL05S, DL05A+
o
Numero Uno: GM05S, GM05A+
o
Plus: DA05S, DA05A+
o
Sonic: TS05AL, TS05S
WITHOUT Ecocutter Table and Stand:
o
Concrete Profiling Wheel: CPE445
o
Crack Chasing Wheel: DCC478
o
Eclipse: DEE005, DEE045
o
Hot-Rod (Granite) HR03A+, HT03A+, HQ03A+, HW03A+
o
Hot-Rod (Marble) HM03A+, HS03A+
o
Katana: DPT125, DPT115
o
Libero: DL05S, DL05A+
o
Numero Uno: GM05S, GM05A+
o
Plus: DA05S, DA05A+
o
Sonic: TS05AL, TS05S
o
Tuck Point: TP04AP
What can I due to maintain my ECC-125 and keep it running like new?
Unplug the tool, remove the blade and belt covers to check and clean the belts after every 100 hours of use. Stone
dust will get inside the covers and onto the belts and pulleys, this can cause the belts to wear and the pulleys to slip.
The belts should be replaced when showing signs of wear. A worn or stretched belt will not be able to center itself on
the pulleys and can come off or wear a hole in the belt cover.
After every 300 hours of use you should check the carbon brushes.
Replacement of the belts and carbon brushes on a periodic basis is the first step to any type of maintenance. If
complications begin to arise during cutting, or if unusual noises occur, check the belts and pulleys. If the unit is working
correctly and you still hear the noise, this could be an indication that a bearing is going. If this occurs, then we
recommend that you send your tool in for repair. Our Tool Repair Department will disassemble and evaluate the tool,
and provide an estimate for your approval, before repairing this tool. The sooner a tool is checked after noticing an
abnormal noise, the less likely there will be a significant amount of damage.
What can I do if my ECC-125/225 breaks down and I need to complete the job immediately?
First check the belts and carbon brushes, if they appear worn out, replace them with genuine Alpha parts and test the
ECC-125/225 before attempting to resume cutting. If the problem still persists, contact the Tool Repair Department at
Alpha Professional Tools® at 800-648-7229 ext 281 to speak to a service technician.
What is the metal attachment that comes with the tool used for?
This item is called the Guide Ruler or TT Ruler Guide. It is designed to enhance the cutting performance of the
ECC-125/225 by providing a guide that will work against the straight edge of the stone or a rail of some type clamped
to the stone surface for use without the table and stand.
There are two felt strips supplied with my ECC-125/225, what are they used for?
These two felt strips can be attached to the bottom of the base plate to prevent any possible scratching of the material
when using the ECC-125/225 without the table and stand. Without these felt strips, the base plate would slide directly
on the surface of the material.
Can I reuse my dust bag?
Yes. The dust bag can be emptied and re-used. However; you may need to eventually reorder a new bag.
Helpful Hints
●
Carry the table by the handle only. Do Not carry by the rails. Attempting to carry the table by the rails will damage
or bend the rails.
Document # 6030 - Rev.-November 2010
www.alpha-tools.com
Page 3 of 4