- ページ 2

インバーター Epever Tracer5210EPLIのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Epever Tracer5210EPLI 6 ページ。 Mppt solar charge controller with built in led driver

ページを印刷する

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

4) Real-time Control

Control the load ON/OFF time through setting real-time clock.

NOTE: In the mode of Light ON/OFF and Light ON/Timer, the Load is

turned on after 10Min. delay.

8. Protection

 PV Reverse Polarity

Fully protection against PV reverse polarity, correct the wire connection to resume

normal operation.

WARNING: Controller will be damaged when the PV array straight

polarity and the actual operation power of the PV array is 1.5 times

greater than the rated charge power!

 Battery Reverse Polarity

Fully protection against battery reverse polarity, correct the wire connection to

resume normal operation.

 Battery Over Voltage

When the battery voltage reaches to the set point of Over Voltage Disconnect Voltage,

the controller will stop charging the battery to protect the battery from being over

charged to break down.

 Battery Over Discharge

When the battery voltage reaches to the set point of Low Voltage Disconnect Voltage,

the controller will stop discharging the battery to protect the battery from being over

discharged to break down.

 Battery Overheating

The controller detects the environment temperature through the external temperature

sensor. If the environment temperature exceeds 65 º C, the controller will

automatically start the overheating protection to stop working, and recover below 55

º C.

 Load Short Circuit

Load will be switched off when load short circuit (≥4 times rated current) happens.

Controller will automatically attempt to reconnect load for 5 times. If short circuit

protection still exist after controller's 5 times attempts, user have to clear short

circuit ,then restart the controller or wait for one night-day cycle (night time>3 hours).

 Temperature sensor break down

If the temperature sensor short-circuited or damaged, the controller will be charging

or discharging at the default temperature 25 º C to prevent the battery damaged from

overcharging or over discharged.

 High Voltage Transients

The controller is protected against small high voltage transients. In lightning prone

areas, additional external suppression is recommended.

9. Troubleshooting

Faults

Possible reasons

LED Charging indicator

turn off during daytime

when sunshine falls on

array disconnection

PV modules properly

Battery voltage maybe

No LED indicator

less than 9V

Battery LED indicator

Battery over voltage

green fast Flashing

10. Technical Specifications

Item

Models

Nominal system voltage

Battery input voltage range

Rated charge current

Rated charge power

①

Max. PV open circuit voltage

MPP Voltage range

Max. output current

Max. output power

Output voltage range

Load open circuit voltage

Maximum output efficiency

Output current control accuracy

Battery Type

Equalize Charging Voltage

※

Boost Charging Voltage

Float Charging Voltage

※

Low Voltage Reconnect Voltage

※

Low Voltage Disconnect Voltage

※

Self-consumption

Temperature compensation

coefficient

Communication

Working environment

temperature

Enclosure

Overall dimension

Mounting hole size

Mounting dimension

Power cable

Net weight

※

Above parameters are in 12V system at 25 º C, please double the values in 24V system.

Troubleshooting

Confirm

that

battery wire connections

are correct and tight

Measure battery voltage

with the multi-meter.

Min.9V can start up the

controller

Check if battery voltage is

higher than OVD, and

Tracer1305EPLI

Tracer2606EPLI

12VDC

9～16VDC

10A/12V

10A

130W/12V

260W/24V

48V （Min. Temp.）

58V at minimum operating environment temperature

46V at 25℃ environment temperature

45V(25℃)

( Battery voltage+2V)～36V

3.3A

100W

( Max. battery

( Max. battery voltage+2V)～58V

voltage+2V)～46V

46V

124×89×30mm

88×76mm

PV/BAT:14AWG(2.5mm

LOAD:18AWG(1.0mm

0.51kg

0.52kg

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

Battery LED indicator

red

Battery LED indicator

red flashing

Charging(green) and

battery indicator

(orange)flashing

simultaneously

Powering on normally,

the load is off

The dimming function is

invalid

Parameter settings fail

①When the battery is over discharged, the battery indicator will be red and the load will be off all the

time before the voltage is more than the Low Voltage Reconnect Voltage (LVRV). In order to judge the

system is normal or not, firstly measuring the battery voltage whether is more than LVRV, if not,

restarting the controller to detect the load whether it is normal.

Note: The LVRV can be set, but it must pay more attention that it maybe damages the battery if

the LVRV is too low.

11. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

and

 PV or load current, voltage or power exceeding the rated value of controller.

 The controller is working temperature exceed the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Tracer3906EPLI

Tracer5206EPLI

15A

20A

195W/12V

260W/12V

390W/24V

520W/24V

4.5A

6.6A

130W

200W

58V

96%

≤2%

Sealed(Default) / Gel / Flooded /User

Sealed:14.6V / Gel:— / Flooded:14.8V / User:9～17V

Sealed:14.4V / Gel:14.2V / Flooded:14.6V / User:9～17V

Sealed / Gel / Flooded:13.8V / User:9～17V

Sealed / Gel / Flooded:12.6V / User:9～17V

Sealed / Gel / Flooded:11.1V / User:9～17V

≤15mA/12V;≤22mA/24V

-3mV/℃/2V

IR communication

-40℃～+60℃

IP68(1.5m,72h)

150×93.5×32.7mm

153×105×52.1mm

Φ3.5mm

120×83mm

120×94mm

)

PV/BAT:12AWG(4mm

)

LOAD:16AWG(1.5mm

0.75kg

1.19kg

Battery

①

over discharged

Battery Overheating

System voltage error

①The connecting wires

are error or

virtually connected

②Load mode is not

appropriate.

③This controller does not

match with the LED light.

④Output short circuit.

The controller does not

match with the LED light

source. This product is a

step-up voltage control, If

input voltage is lower than

the rated voltage, it is not

working.

Infrared communication

error

Any changes without prior notice! Version number：V3.1

Tracer2610EPLI

Tracer3910EPLI

12/24VDC Auto

9～32VDC

10A

15A

130W/12V

195W/12V

260W/24V

390W/24V

95V at minimum operating environment temperature

92V at 25℃ environment temperature

( Battery voltage+2V)～72V

3.3A

4.5A

100W

130W

( Max. battery voltage+2V)～80V

124×89×30mm

150×93.5×32.7mm

88×76mm

120×83mm

)

PV/BAT:14AWG(2.5mm

)

LOAD:18AWG(1.0mm

0.52kg

0.75kg

disconnect the PV

When the battery voltage

is restored to or above

LVR point (low voltage

reconnect voltage), the

load will recover

The controller will

automatically turn the

system off. But while the

temperature decline to be

below 50 º C, the controller

will resume.

Check whether the battery

voltage match with the

controller's working

voltage, If not please

change to a suitable

battery or reset the

working voltage

① Check the connecting

cable.

② Check the load's mode

and parameters.

③The voltage of LED light

is not within the output

voltage range of controller.

④Check the connecting

cables and LED light.

①Replace the LED light.

②Reduce system rated

voltage grade and replace

the product model.

For example 24V system

change to 12V system,

and replace the

corresponding controller

Refer to handheld the user

device manual

Tracer5210EPLI

20A

260W/12V

520W/24V

6.6A

200W

80V

153×105×52.1mm

120×94mm

)

PV/BAT:12AWG(4mm

)

LOAD:16AWG(1.5mm

)

1.18kg