- ページ 2
ロックス Dieckmann Riva SeriesのPDF 組み立て説明書をオンラインで閲覧またはダウンロードできます。Dieckmann Riva Series 2 ページ。
ページを印刷するAssembly Instructions Model Riva
DIN EN 1906
DIN EN 179
1
lever - lever - set
⑥
⑤
⑨
↓
③
⑦
↓
↓
↓
①
⑧
↓
Ⓐ
Ⓐ
↓
⑦
②
3
inactive leaf set
⑨
⑥
⑤
③
↓
Ⓐ
⑦
↓
↓
↓
Ⓐ
5
lever - set for WC
⑨
⑥
⑤
↓
③
Ⓐ
⑦
↓
↓
↓
⑨
Ⓐ
⑧
⑥
⑤
Ⓐ
↓
⑫
⑦
②
General maintenance and cleaning instructions: To remove light soi-
ling, gently clean with a soft cloth slightly moistened with warm water. For
heavier soiling, use of a specialist metal cleaner is recommended. Abois
using harsh abrasives or general household cleaning agents.
The testing of door hardware for escape doors,
fire and smoke protection is carried out as a
complete assembly therefore the components
may only be used together, not separately. The
installation must be in accordance with the ins-
tructions and carried out by a qualified person.
Failure to comply with the above voids any claim
under warranty.
DIN 18273
ÖNorm B 3859
2
set with anti-panic function
⑥
⑨
⑨
↓
↓
⑧
⑧
Ⓐ
②
4
half-set
⑧
↓
Ⓐ
③
Ⓐ
①
②
Ⓐ
6
knob - lever set
⑩
⑨
③
↓
↓
⑨
Ⓐ
⑧
⑥
⑪
②
① profile cylinder
② cylinder retaining screw
③ spindle with plug
④ spindle for locks with split follower
⑤
⑨
④
⑤ steel base plate interior
⑦
↓
↓
↓
↓
⑥ steel base plate exterior
①
⑦ M5 hexagon head bolts
⑧
↓
⑧ # 3 allen key
⑨ cover plate
Ⓐ
↓
⑩ fixed knob on plate
⑦
⑪ cover plate with turn snib
⑫ spindle for privacy bolt
Ⓐ screw holes
Place the included drilling template over the profile
cylinder and spindle and mark the position of the
screw holes on both sides of the door.
Remove the lock to avoid damage.
⑨
⑤
Drill small starter holes with a Ø 7 mm drill bit from
⑦
↓
one side as far as the middle of the door. Repeat this
↓
↓
↓
procedure on the other side of the door. (Important:
drill holes for half-sets from one side of the door
only!)
⑧
↓
⑤
Enlarge with a 10 mm drill bit from both sides to 8
⑨
mm deep. (Reminder: for half sets (fig. 4), drill from
one side only!)
↓
⑦
Remove any drilling residue from the lock pocket and
install the lock. Assemble the rose bases and fix with
bolts provided. Ensure the handle release is in a lo-
cked position.
Push the handle onto the spindle until it locks into
the rosette. Tighten the grub screw.
⑤
In the case of entrance door fittings (fig. 6), fix the
Ⓐ
⑦
spindle in the base plate before assembling.
↓
⑨
↓
↓
⑨
⑤
⑧
↓
Ⓐ
⑦
①
To disassemble the handle: ensure the lever is in a
unlocked position, then loosen the grub screw and
remove the handle.
handle release
Version 1.0
(not included)
(not included)
→
unlocked
locked