- ページ 5
ラボラトリー機器 Olympus BH-NREのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Olympus BH-NRE 17 ページ。 Modular revolving nosepiece
ページを印刷する
Recommended Solvents
Some sort of solvent will be needed to clean the old
grease from the components of the BH-NRE modular
revolving nosepiece assembly. Solvents that can be
used are acetone, diethyl ether, heptane, hexane,
mineral spirits, turpentine, and xylene. Mineral spirits
works well with both Plastilube® and Mobilgrease28®.
Safety Considerations with Solvents
Regardless of which solvents are chosen, make sure
that adequate ventilation is present during the cleaning
process, and that any necessary personal protective
equipment is utilized to minimize exposure. Consult the
safety data sheet (SDS or MSDS) before using any
unfamiliar solvents. Many of the solvents listed above
are flammable and their vapors may represent an
explosion hazard if mishandled. Whichever solvents are
chosen, be sure to follow all of the manufacturer's
instructions and safety precautions.
Solvent Compatibility with Parts and Finishes
Many solvents will damage the finish of painted
surfaces or will dissolve or damage plastic parts
(isopropyl alcohol or 409 Cleaner may be safely used to
clean most painted surfaces). Do not allow untested
solvents to contact any plastic parts or painted surfaces.
Before using a solvent to clean plastic parts or painted
surfaces, test a small amount of the solvent in an
inconspicuous area (such as inside a plastic knob) to
ensure compatibility with the plastic part or painted
surface. Never use xylene to clean nylon parts, as
xylene dissolves nylon.
trichloroethylene will cause swelling of nylon due to
solvent absorption.
The list of solvents generally
considered safe for nylon includes acetone, diethyl
ether, heptane, mineral spirits, naphthalene, and
turpentine.
Before Starting the Overhaul
Remove the Objectives from the Nosepiece
Before beginning the teardown of the BH-NRE modular
revolving nosepiece assembly, remove the nosepiece
assembly from the microscope stand, remove all the
objectives from the revolving turret, and store the
objectives someplace where they will be protected from
physical damage, dust, and debris.
Label Parts for Identification and Reassembly
During the teardown of the BH-NRE modular revolving
nosepiece assembly, be sure to bag and tag the various
parts as they are removed, to prevent their loss and to
facilitate
their
proper
subsequent reassembly process.
Complete Teardown, Cleaning, and Reassembly of the Olympus BH-NRE Modular Revolving Nosepiece
Isopropyl alcohol and
identification
during
Service the BH-NRE Modular Nosepiece
Figure 2
shows the 4-position BH-NRE modular
revolving nosepiece assembly used on the Olympus BH
and BH-2 microscope stands.
Figure 2 – The BH-NRE modular revolving nosepiece
The BH-NRE modular revolving nosepiece assembly
consists of a 4-position turret assembly, which is made
up of an inner stationary base, an outer revolving turret,
miscellaneous parts and a protective cover. Attached to
the turret assembly is a machined dovetail slide, for
mounting the BH-NRE onto the BH/BH-2 stand (see
Figure
3).
Figure 3 – Basic components of the BH-NRE
The procedure to disassemble, clean/re-grease, and
reassemble the BH-NRE modular revolving nosepiece
assembly is detailed in the following sections.
Remove the Cover from the Turret Assembly
Use a suitable JIS screwdriver to remove the three
the
M2X3 countersink screws securing the protective cover
Page 5 of 17
Revision 3